[chirp_users] Chirp under Linux

[AKA Macgyver]

Is the radio turned ON? Sometimes you have to not only turn them on but
also crank the volume to max.

On Sat, Dec 7, 2019, 6:44 PM Tom Henderson <Tom at henderson4.us> wrote:

> Adding yourself to the "dialout" group should prevent you from having to
> do this.
>
> Tom Henderson
>
> On 12/7/19 6:58 PM, Pat Anderson wrote:
>
> Oops, I should have said I am running Ubuntu Linux. Can't say anything if
> you are running something other than Linux.
>
>
> On Sat, Dec 7, 2019 at 5:56 PM Pat Anderson <anderson5420 at gmail.com>
> wrote:
>
>> Try this. Before you try to read from the radio, do "chmod 777
>> /dev/ttyUSB0".  I have a Baofeng UV82HP and CHIRP reads and writes just
>> fine once I have done this.
>>
>> Pat Anderson
>> KD7OAC
>>
>> On Sat, Dec 7, 2019 at 5:48 PM Phil <phillor9 at gmail.com> wrote:
>>
>>> Thank you for reading this.
>>>
>>> I bought a Baofeng UV-82HP about four months ago and I cannot get Chirp
>>> to read from the radio, or in fact to do anything with the radio.
>>>
>>> I'm running Chirp under Kubuntu and have tried every Chip daily version
>>> over the past four months. This is the error message that I receive when
>>> I attempt to read from the radio:
>>>
>>> "Radio did not respond"
>>>
>>> These are the entered parameters:
>>>
>>> /dev/ttyUSB0
>>> Baofeng
>>> UV-82HP
>>>
>>> I have read and write access to the serial port which is the same port
>>> that I use for several application including programming an Arduino
>>> board. I have tried several different Baofeng models, just in case, with
>>> the same result.
>>>
>>> I've trimmed the plastic from the plug so that it slips into the radio's
>>> sockets more easily. I've attempted to read from the radio in both
>>> channel and frequency modes. Finally, I've searched the Internet for
>>> even the slightest clue but to no avail.
>>>
>>> I do not know anyone who owns a Baofeng radio or who uses Chirp. So this
>>> mailing list is my last hope.
>>>
>>> Any clues at all will greatly appreciated.
>>>
>>> --
>>> Regards,
>>> Phil
>>>
>>> _______________________________________________
>>> chirp_users mailing list
>>> chirp_users at intrepid.danplanet.com
>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>> This message was sent to Pat Anderson at anderson5420 at gmail.com
>>> To unsubscribe, send an email to
>>> chirp_users-unsubscribe at intrepid.danplanet.com
>>>
>>
> _______________________________________________
> chirp_users mailing listchirp_users at intrepid.danplanet.comhttp://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to Tom KM4UQB at tom at henderson4.us
> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
>
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to Ryan McOmber at volksmech at gmail.com
> To unsubscribe, send an email to
> chirp_users-unsubscribe at intrepid.danplanet.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20191207/b1f796d2/attachment.html