[chirp_users] Chirp under Linux

[Tom Henderson]

Adding yourself to the "dialout" group should prevent you from having to 
do this.

Tom Henderson

On 12/7/19 6:58 PM, Pat Anderson wrote:
> Oops, I should have said I am running Ubuntu Linux. Can't say anything 
> if you are running something other than Linux.
>
>
> On Sat, Dec 7, 2019 at 5:56 PM Pat Anderson <anderson5420 at gmail.com 
> <mailto:anderson5420 at gmail.com>> wrote:
>
>     Try this. Before you try to read from the radio, do "chmod 777
>     /dev/ttyUSB0".  I have a Baofeng UV82HP and CHIRP reads and writes
>     just fine once I have done this.
>
>     Pat Anderson
>     KD7OAC
>
>     On Sat, Dec 7, 2019 at 5:48 PM Phil <phillor9 at gmail.com
>     <mailto:phillor9 at gmail.com>> wrote:
>
>         Thank you for reading this.
>
>         I bought a Baofeng UV-82HP about four months ago and I cannot
>         get Chirp
>         to read from the radio, or in fact to do anything with the radio.
>
>         I'm running Chirp under Kubuntu and have tried every Chip
>         daily version
>         over the past four months. This is the error message that I
>         receive when
>         I attempt to read from the radio:
>
>         "Radio did not respond"
>
>         These are the entered parameters:
>
>         /dev/ttyUSB0
>         Baofeng
>         UV-82HP
>
>         I have read and write access to the serial port which is the
>         same port
>         that I use for several application including programming an
>         Arduino
>         board. I have tried several different Baofeng models, just in
>         case, with
>         the same result.
>
>         I've trimmed the plastic from the plug so that it slips into
>         the radio's
>         sockets more easily. I've attempted to read from the radio in
>         both
>         channel and frequency modes. Finally, I've searched the
>         Internet for
>         even the slightest clue but to no avail.
>
>         I do not know anyone who owns a Baofeng radio or who uses
>         Chirp. So this
>         mailing list is my last hope.
>
>         Any clues at all will greatly appreciated.
>
>         -- 
>         Regards,
>         Phil
>
>         _______________________________________________
>         chirp_users mailing list
>         chirp_users at intrepid.danplanet.com
>         <mailto:chirp_users at intrepid.danplanet.com>
>         http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>         This message was sent to Pat Anderson at
>         anderson5420 at gmail.com <mailto:anderson5420 at gmail.com>
>         To unsubscribe, send an email to
>         chirp_users-unsubscribe at intrepid.danplanet.com
>         <mailto:chirp_users-unsubscribe at intrepid.danplanet.com>
>
>
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to Tom KM4UQB at tom at henderson4.us
> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20191207/5bc3df90/attachment.html