<div dir="auto">Is the radio turned ON? Sometimes you have to not only turn them on but also crank the volume to max.</div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sat, Dec 7, 2019, 6:44 PM Tom Henderson <<a href="mailto:Tom@henderson4.us">Tom@henderson4.us</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div text="#000000" bgcolor="#FFFFFF">
<p>Adding yourself to the "dialout" group should prevent you from
having to do this.<br>
</p>
<pre cols="72">Tom Henderson</pre>
<div>On 12/7/19 6:58 PM, Pat Anderson wrote:<br>
</div>
<blockquote type="cite">
<div dir="ltr">Oops, I should have said I am running Ubuntu Linux.
Can't say anything if you are running something other than
Linux.
<div><br>
</div>
</div>
<br>
<div class="gmail_quote">
<div dir="ltr" class="gmail_attr">On Sat, Dec 7, 2019 at 5:56 PM
Pat Anderson <<a href="mailto:anderson5420@gmail.com" target="_blank" rel="noreferrer">anderson5420@gmail.com</a>> wrote:<br>
</div>
<blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
<div dir="ltr">Try this. Before you try to read from the
radio, do "chmod 777 /dev/ttyUSB0". I have a Baofeng UV82HP
and CHIRP reads and writes just fine once I have done this.
<div><br>
</div>
<div>Pat Anderson</div>
<div>KD7OAC </div>
</div>
<br>
<div class="gmail_quote">
<div dir="ltr" class="gmail_attr">On Sat, Dec 7, 2019 at
5:48 PM Phil <<a href="mailto:phillor9@gmail.com" target="_blank" rel="noreferrer">phillor9@gmail.com</a>>
wrote:<br>
</div>
<blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Thank you for reading
this.<br>
<br>
I bought a Baofeng UV-82HP about four months ago and I
cannot get Chirp <br>
to read from the radio, or in fact to do anything with the
radio.<br>
<br>
I'm running Chirp under Kubuntu and have tried every Chip
daily version <br>
over the past four months. This is the error message that
I receive when <br>
I attempt to read from the radio:<br>
<br>
"Radio did not respond"<br>
<br>
These are the entered parameters:<br>
<br>
/dev/ttyUSB0<br>
Baofeng<br>
UV-82HP<br>
<br>
I have read and write access to the serial port which is
the same port <br>
that I use for several application including programming
an Arduino <br>
board. I have tried several different Baofeng models, just
in case, with <br>
the same result.<br>
<br>
I've trimmed the plastic from the plug so that it slips
into the radio's <br>
sockets more easily. I've attempted to read from the radio
in both <br>
channel and frequency modes. Finally, I've searched the
Internet for <br>
even the slightest clue but to no avail.<br>
<br>
I do not know anyone who owns a Baofeng radio or who uses
Chirp. So this <br>
mailing list is my last hope.<br>
<br>
Any clues at all will greatly appreciated.<br>
<br>
-- <br>
Regards,<br>
Phil<br>
<br>
_______________________________________________<br>
chirp_users mailing list<br>
<a href="mailto:chirp_users@intrepid.danplanet.com" target="_blank" rel="noreferrer">chirp_users@intrepid.danplanet.com</a><br>
<a href="http://intrepid.danplanet.com/mailman/listinfo/chirp_users" rel="noreferrer noreferrer" target="_blank">http://intrepid.danplanet.com/mailman/listinfo/chirp_users</a><br>
This message was sent to Pat Anderson at <a href="mailto:anderson5420@gmail.com" target="_blank" rel="noreferrer">anderson5420@gmail.com</a><br>
To unsubscribe, send an email to <a href="mailto:chirp_users-unsubscribe@intrepid.danplanet.com" target="_blank" rel="noreferrer">chirp_users-unsubscribe@intrepid.danplanet.com</a><br>
</blockquote>
</div>
</blockquote>
</div>
<br>
<fieldset></fieldset>
<pre>_______________________________________________
chirp_users mailing list
<a href="mailto:chirp_users@intrepid.danplanet.com" target="_blank" rel="noreferrer">chirp_users@intrepid.danplanet.com</a>
<a href="http://intrepid.danplanet.com/mailman/listinfo/chirp_users" target="_blank" rel="noreferrer">http://intrepid.danplanet.com/mailman/listinfo/chirp_users</a>
This message was sent to Tom KM4UQB at <a href="mailto:tom@henderson4.us" target="_blank" rel="noreferrer">tom@henderson4.us</a>
To unsubscribe, send an email to <a href="mailto:chirp_users-unsubscribe@intrepid.danplanet.com" target="_blank" rel="noreferrer">chirp_users-unsubscribe@intrepid.danplanet.com</a></pre>
</blockquote>
</div>
_______________________________________________<br>
chirp_users mailing list<br>
<a href="mailto:chirp_users@intrepid.danplanet.com" target="_blank" rel="noreferrer">chirp_users@intrepid.danplanet.com</a><br>
<a href="http://intrepid.danplanet.com/mailman/listinfo/chirp_users" rel="noreferrer noreferrer" target="_blank">http://intrepid.danplanet.com/mailman/listinfo/chirp_users</a><br>
This message was sent to Ryan McOmber at <a href="mailto:volksmech@gmail.com" target="_blank" rel="noreferrer">volksmech@gmail.com</a><br>
To unsubscribe, send an email to <a href="mailto:chirp_users-unsubscribe@intrepid.danplanet.com" target="_blank" rel="noreferrer">chirp_users-unsubscribe@intrepid.danplanet.com</a></blockquote></div>