[chirp_users] problem with baofeng uv-5r

Amnon Zohar
Mon Nov 12 13:57:52 PST 2018


Anybody has an idea how to release? Maybe contact spray?
Are the contactor accesible by opening the unit?

בתאריך יום ב׳, 12 בנוב' 2018, 22:07, מאת Glenn At Home <
GlennErvin at cableone.net>:

> I have one that this happened to, and I can only use the external
> speaker-mic now.
> Glenn
> ----- Original Message -----
> *From:* Amnon Zohar <amnon.zohar at gmail.com>
> *To:* Discussion of CHIRP <chirp_users at intrepid.danplanet.com>
> *Sent:* Monday, November 12, 2018 10:26 AM
> *Subject:* Re: [chirp_users] problem with baofeng uv-5r
>
> Tx jim ill check with external mic. Any suggestion to solve it?
>
> בתאריך יום ב׳, 12 בנוב' 2018, 16:36, מאת Jim Unroe <rock.unroe at gmail.com>:
>
>> On Mon, Nov 12, 2018 at 8:55 AM Amnon Zohar <amnon.zohar at gmail.com>
>> wrote:
>> >
>> > not exactly a chirp issue:
>> >
>> > i have few uv-5r's
>> >
>> > one of them can only receive
>> > while transmitting the others receive only the bip but not the voice~
>> > what might be the reason besides a defective mic
>>
>> When a external device (speaker/mic, programming cable, etc.) is
>> plugged into the socket of the radio, 2 contacts are lifted to
>> disconnect the internal microphone and the internal speaker. It is
>> common in these radios for the contact to not fully return to the
>> initial position when the 2-pin plug is removed. When this happens,
>> the internal mic and/or speaker remains disconnected.
>>
>> >
>> > (while checking i found out i cannot manualy change menu 5 from wide to
>> narrow . it remais as programmed - this IS a chirp issue(
>>
>> This is not a CHIRP issue. This is how the radio works. You cannot
>> permanently change any parameter of a programmed memory. You can only
>> temporarily change TX power output level by tapping the [#] or swap
>> the TX and RX frequencies by tapping the [*] to put the radio into
>> "reverse" mode.
>>
>> You can only manually update the TX frequency and either the TX DCS
>> code or TX CTCSS tone by entering the values in the top (A) VFO and
>> then write the new values to the appropriate memory using menu 28
>> (MEM-CH). To change any other parameter, including menu 5 (W/N), you
>> must erase the memory and program the memory back from scratch using
>> the top (A) VFO or use programming software such as CHIRP.
>>
>> >
>> > --
>> > Amnon
>>
>> Jim KC9HI
>> _______________________________________________
>> chirp_users mailing list
>> chirp_users at intrepid.danplanet.com
>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>> This message was sent to amnon at amnon.zohar at gmail.com
>> To unsubscribe, send an email to
>> chirp_users-unsubscribe at intrepid.danplanet.com
>>
> ------------------------------
>
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to Glenn at glennervin at cableone.net
> To unsubscribe, send an email to
> chirp_users-unsubscribe at intrepid.danplanet.com
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to amnon at amnon.zohar at gmail.com
> To unsubscribe, send an email to
> chirp_users-unsubscribe at intrepid.danplanet.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20181112/44c6f452/attachment.html 


More information about the chirp_users mailing list