[chirp_users] Radioddity QB25 NOT QYT KT7900D

[Dennis Wage]

Delete channel 135 and see what happens

Dennis M. Wage

245 Corum Hill Road
Castalian Springs, TN 37031
(615) 310-4242 Cell
(615) 562-5128 Home
http://hammondb3organ.net
http://overdubs.net

On Sun, Apr 1, 2018 at 5:14 PM, W8RGB Gary <W8RGB at live.com> wrote:

> The set up is Windows.
>
>
> The Radioddity SW works as well as it can: reads and writes but crashes at
> Ch 135... Channels before that write Okay.
>
>
> It is NOT a driver issue.
>
>
> Why does Chirp (ver 3/31) change the Radioddity QB25 to QYT Kt7900D?  When
> I first purchased the radio last September, I tried to Chirp using KT7900D
> with no luck.
>
>
>
>
> *    73  Gary  W8RGB *
>
>
> ------------------------------
> *From:* chirp_users-bounces at intrepid.danplanet.com <
> chirp_users-bounces at intrepid.danplanet.com> on behalf of Jim Unroe <
> rock.unroe at gmail.com>
> *Sent:* Sunday, April 1, 2018 17:43
> *To:* Discussion of CHIRP
> *Subject:* Re: [chirp_users] Radioddity QB25 NOT QYT KT7900D
>
> On Sun, Apr 1, 2018 at 4:58 PM, W8RGB Gary <W8RGB at live.com> wrote:
> > So I get one of those Radioddity QB25 radios. I was so glad to see that
> > Chirp supports it!
> >
> > When I choose "Download from Radio," I can select Radioddity and QB25.
> When
> > I select "OK," the
> >     display shows QYT and KT7900D
> >     the Radio Identification is successful
> >     about 1/3 through the 'cloning' this error occurs...
> >          Invalid header at block x1180
> > What is the process for programing this radio?
> >
> > Thank you!
> >
> >     73  Gary  W8RGB
>
> Hi Gary,
>
> You didn't provide any details about your setup. Assuming you are
> using Windows and probably purchased the programming cable from
> Radioddity, I would imaging that this is a driver issue. If the
> programming cable with manufactured with a counterfeit Prolific chip,
> you must download, install and select the Prolific v3.2.0.0 device
> driver. The driver automatically installed by Windows is intentionally
> incompatible with counterfeit Prolific chips.
>
> This page has a link to the driver and instructions for installing it:
> http://www.miklor.com/COM/UV_Drivers.php
>
> I have multiple Prolific driver versions installed and switch between
> then a will to test for counterfeit Prolific type chips. Nearly all
> programming cables that identify themselves to Windows as having a
> Prolific chip in them is made with the counterfeit chip. I keep the
> v3.2.0.0 driver selected for daily use because it works for both the
> unauthorized chip copy as well as the rare genuine Prolific chip.
>
> Jim KC9HI
>
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to Dennis Wage at dwage at dwage.com
> To unsubscribe, send an email to chirp_users-unsubscribe@
> intrepid.danplanet.com
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20180401/e1238085/attachment.html