[chirp_users] Kenwood TK-762H

[John LaMartina]

Refer to:
http://www.miklor.com/COM/UV_ErrorMess.php





 

From: chirp_users-bounces at intrepid.danplanet.com [mailto:chirp_users-bounces at intrepid.danplanet.com] On Behalf Of Jon S
Sent: Thursday, August 11, 2016 6:17 PM
To: Jardy Dawson; Discussion of CHIRP
Subject: Re: [chirp_users] Kenwood TK-762H

 

image1.JPG


On Aug 11, 2016, at 16:57, Jardy Dawson via chirp_users <chirp_users at intrepid.danplanet.com> wrote:

You don't say the error, but most problems come from having a fake Prolific chip. Go to Device Manager and check your comm port.  If it says Prolific, roll your driver to 3.2.0.0.  This can be found at Miklor.com.

Jardy Dawson

WA7JRD Ham Radio

 

Message relayed through The Senior Boston Relay Race baton pass.


On Aug 11, 2016, at 14:30, Jon S <savageman208 at gmail.com> wrote:

anyone know why when i try to program my 857d that i get an error message when cloning?

 

On Wed, Aug 10, 2016 at 6:58 PM, Pavel Milanes (CO7WT) <pavelmc at gmail.com> wrote:

Hi Tim, (I was off the grid by family vacations)

If the lights are off you have 90% chance of not having power to the interface, but, if you use a USB interface it may work... I have to check in the schematics but I'm pretty sure it will work with a USB programmer.

73 Pavel CO7WT



El 08/08/16 a las 11:35, Tim Billingsley escribió:

I will check that as time allows and I bet you are correct asI do not believe any of these old men light up any longer. I will advise as time allows.

73

 

On Fri, Jul 22, 2016 at 4:44 PM, Pavel Milanes (CO7WT) <pavelmc at gmail.com> wrote:

Hi Tim, sorry to hear about your heard issues.

Can you please confirms that the cable interface is working? (it looks to me as a interface problem)

Also, your radios has the LCD backlight on?

There is a know issue with this radios about this: usually the kenwood interface for this radios take power from the radio not from the PC, and the power is taken from the same rail the LCD leds are powered. 

For some reason with time (or a mic cable short) a medium power resistor burn out in the main board and get the front panel without +12V, that not a problem to the normal operation as it works on +5v, but the backlight gone off and the programmer has no power to feed from and always fails to operate.

Can you check that please?

73.

El 22/07/16 a las 09:32, Tim Billingsley escribió:

I apologize for the long delay.    With health issues and an amount of tracel out of the way I have just tested 4 radios. 2 TK-762 and 2 TK-762H none worked. The CHIRP options of TK-760G & TK-762G appears to read from the radio then throws the error  

 

 

ERROR: Traceback (most recent call last):

 

    self.__radio.sync_in()

  File "/usr/lib/python2.7/dist-packages/chirp/drivers/tk760.py", line 410, in sync_in

    self._mmap = do_download(self)

  File "/usr/lib/python2.7/dist-packages/chirp/drivers/tk760.py", line 254, in do_download

    open_radio(radio)

  File "/usr/lib/python2.7/dist-packages/chirp/drivers/tk760.py", line 226, in open_radio

    raise errors.RadioError(msg)

RadioError: Radio refuse to enter into program mode after a few tries

 

ERROR: ----------------

ERROR: Clone failed: Radio refuse to enter into program mode after a few tries

ERROR: --- Exception Dialog: Radio refuse to enter into program mode after a few tries ---

ERROR: None

 

ERROR: ----------------------------

 

 

 

 





-- 
73 Pavel CO7WT.


_______________________________________________
chirp_users mailing list
chirp_users at intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
This message was sent to Tim at kd5ckp at gmail.com
To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com

 





_______________________________________________
chirp_users mailing list
chirp_users at intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
This message was sent to M.Sc. Pavel Milanes Costa at pavelmc at gmail.com
To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com





-- 
73 Pavel CO7WT.


_______________________________________________
chirp_users mailing list
chirp_users at intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
This message was sent to Jon at savageman208 at gmail.com
To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com

 

_______________________________________________
chirp_users mailing list
chirp_users at intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
This message was sent to Jardy at jardy72 at yahoo.com
To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com

_______________________________________________
chirp_users mailing list
chirp_users at intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
This message was sent to Jon at savageman208 at gmail.com
To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20160811/9ef84cb7/attachment.html 
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: image/jpeg
Size: 24819 bytes
Desc: not available
Url : http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20160811/9ef84cb7/attachment.jpe