[chirp_users] Kenwood TK-762H

[Jon S]

> On Aug 11, 2016, at 16:57, Jardy Dawson via chirp_users <chirp_users at intrepid.danplanet.com> wrote:
> 
> You don't say the error, but most problems come from having a fake Prolific chip. Go to Device Manager and check your comm port.  If it says Prolific, roll your driver to 3.2.0.0.  This can be found at Miklor.com.
> 
> Jardy Dawson
> WA7JRD Ham Radio
> 
> Message relayed through The Senior Boston Relay Race baton pass.
> 
> On Aug 11, 2016, at 14:30, Jon S <savageman208 at gmail.com> wrote:
> 
> anyone know why when i try to program my 857d that i get an error message when cloning?
> 
>> On Wed, Aug 10, 2016 at 6:58 PM, Pavel Milanes (CO7WT) <pavelmc at gmail.com> wrote:
>> Hi Tim, (I was off the grid by family vacations)
>> 
>> If the lights are off you have 90% chance of not having power to the interface, but, if you use a USB interface it may work... I have to check in the schematics but I'm pretty sure it will work with a USB programmer.
>> 
>> 73 Pavel CO7WT
>> 
>> 
>>> El 08/08/16 a las 11:35, Tim Billingsley escribió:
>>> I will check that as time allows and I bet you are correct asI do not believe any of these old men light up any longer. I will advise as time allows.
>>> 
>>> 73
>>> 
>>>> On Fri, Jul 22, 2016 at 4:44 PM, Pavel Milanes (CO7WT) <pavelmc at gmail.com> wrote:
>>>> Hi Tim, sorry to hear about your heard issues.
>>>> 
>>>> Can you please confirms that the cable interface is working? (it looks to me as a interface problem)
>>>> Also, your radios has the LCD backlight on?
>>>> 
>>>> There is a know issue with this radios about this: usually the kenwood interface for this radios take power from the radio not from the PC, and the power is taken from the same rail the LCD leds are powered. 
>>>> For some reason with time (or a mic cable short) a medium power resistor burn out in the main board and get the front panel without +12V, that not a problem to the normal operation as it works on +5v, but the backlight gone off and the programmer has no power to feed from and always fails to operate.
>>>> 
>>>> Can you check that please?
>>>> 73.
>>>> 
>>>>> El 22/07/16 a las 09:32, Tim Billingsley escribió:
>>>>> I apologize for the long delay.    With health issues and an amount of tracel out of the way I have just tested 4 radios. 2 TK-762 and 2 TK-762H none worked. The CHIRP options of TK-760G & TK-762G appears to read from the radio then throws the error 
>>>>> 
>>>>> 
>>>>> ERROR: Traceback (most recent call last):
>>>>> 
>>>>>     self.__radio.sync_in()
>>>>>   File "/usr/lib/python2.7/dist-packages/chirp/drivers/tk760.py", line 410, in sync_in
>>>>>     self._mmap = do_download(self)
>>>>>   File "/usr/lib/python2.7/dist-packages/chirp/drivers/tk760.py", line 254, in do_download
>>>>>     open_radio(radio)
>>>>>   File "/usr/lib/python2.7/dist-packages/chirp/drivers/tk760.py", line 226, in open_radio
>>>>>     raise errors.RadioError(msg)
>>>>> RadioError: Radio refuse to enter into program mode after a few tries
>>>>> 
>>>>> ERROR: ----------------
>>>>> ERROR: Clone failed: Radio refuse to enter into program mode after a few tries
>>>>> ERROR: --- Exception Dialog: Radio refuse to enter into program mode after a few tries ---
>>>>> ERROR: None
>>>>> 
>>>>> ERROR: ----------------------------
>>>> 
>>>> -- 
>>>> 73 Pavel CO7WT.
>>>> 
>>>> _______________________________________________
>>>> chirp_users mailing list
>>>> chirp_users at intrepid.danplanet.com
>>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>>> This message was sent to Tim at kd5ckp at gmail.com
>>>> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
>>> 
>>> 
>>> 
>>> _______________________________________________
>>> chirp_users mailing list
>>> chirp_users at intrepid.danplanet.com
>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>> This message was sent to M.Sc. Pavel Milanes Costa at pavelmc at gmail.com
>>> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
>> 
>> -- 
>> 73 Pavel CO7WT.
>> 
>> _______________________________________________
>> chirp_users mailing list
>> chirp_users at intrepid.danplanet.com
>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>> This message was sent to Jon at savageman208 at gmail.com
>> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
> 
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to Jardy at jardy72 at yahoo.com
> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to Jon at savageman208 at gmail.com
> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20160811/30a27179/attachment.html 
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image1.JPG
Type: image/jpeg
Size: 24819 bytes
Desc: not available
Url : http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20160811/30a27179/attachment.jpe