[chirp_users] Radio Not Communicating With Laptop

Thu Nov 5 14:07:35 PST 2015

Fantastic !! 
Great "ham" problem solving !!
Dave
K1SIW

Sent from my iPhone 
DSP

On Nov 5, 2015, at 3:10 PM, Rodger Hess <rwhess at dcn.org> wrote:

I rolled back my Prolific driver to version 3.2.0.0 and now all is well.

73
--Rodger
KK6OPW

> On 11/5/2015 11:35 AM, Rodger Hess wrote:
> I am having the same problem as Ray, but also with my TH 9800. The TYT software can't see 
> the radio either. So I don't think it is the plug on the Baofeng cable in my case. 
> 
> Thanks for any help... 
> 
> 73 
> --Rodger 
> KK6OPW 
> 
>> On 11/5/2015 10:53 AM, Gary Runningbear wrote: 
>> Hi Dave, I don't believe there will be a need to be concerned with the port 
>> number if the prolific 2303 driver is downloaded and installed. when I did 
>> that it immediately recognized the circuitry in the patch cord. 
>> On Nov 5, 2015 1:51 PM, "dmdfacp at gmail.com" <dmdfacp at gmail.com> wrote: 
>> 
>>> How about your serial port ?  I just jumped in, so forgive me if I'm 
>>> redundant. 
>>> If you do not know which port is being used, unplug your USB-to-radio 
>>> cable at the computer end. Re-plug it and watch for a small notice 
>>> specifying the port to which the computer connected it. Verify that CHIRP 
>>> is looking at the correct port. 
>>> I just went through this, within the past half hour. Good luck. I'm a 
>>> newbie, here, too. 
>>> Dave 
>>> 
>>> Sent from my iPhone 
>>> DSP 
>>> 
>>> On Nov 5, 2015, at 1:08 PM, Ray Nelson via chirp_users < 
>>> chirp_users at intrepid.danplanet.com> wrote: 
>>> 
>>> I've downloaded the software & installed. I keep getting error message the 
>>> radio is not connected. What am I doing wrong? 
>>> 
>>> Sent from my iPad 
>>> _______________________________________________ 
>>> chirp_users mailing list 
>>> chirp_users at intrepid.danplanet.com 
>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users 
>>> To unsubscribe, send an email to 
>>> chirp_users-unsubscribe at intrepid.danplanet.com 
>>> 
>>> _______________________________________________ 
>>> chirp_users mailing list 
>>> chirp_users at intrepid.danplanet.com 
>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users 
>>> To unsubscribe, send an email to 
>>> chirp_users-unsubscribe at intrepid.danplanet.com 
>>> 
>>> 
>>> 
>>> Hi Dave, I don't believe there will be a need to be concerned with the port number if the prolific 2303 driver is downloaded and installed. when I did that it immediately recognized the circuitry in the patch cord. 
>>> 
>>> On Nov 5, 2015 1:51 PM, "dmdfacp at gmail.com <mailto:dmdfacp at gmail.com>" <dmdfacp at gmail.com <mailto:dmdfacp at gmail.com>> wrote: 
>>> 
>>>     How about your serial port ?  I just jumped in, so forgive me if 
>>>     I'm redundant. 
>>>     If you do not know which port is being used, unplug your 
>>>     USB-to-radio cable at the computer end. Re-plug it and watch for 
>>>     a small notice specifying the port to which the computer 
>>>     connected it. Verify that CHIRP is looking at the correct port. 
>>>     I just went through this, within the past half hour. Good luck. 
>>>     I'm a newbie, here, too. 
>>>     Dave 
>>> 
>>>     Sent from my iPhone 
>>>     DSP 
>>> 
>>>     On Nov 5, 2015, at 1:08 PM, Ray Nelson via chirp_users 
>>>     <chirp_users at intrepid.danplanet.com           
>>>     <mailto:chirp_users at intrepid.danplanet.com>> wrote: 
>>> 
>>>     I've downloaded the software & installed. I keep getting error 
>>>     message the radio is not connected. What am I doing wrong? 
>>> 
>>>     Sent from my iPad 
>>>     _______________________________________________ 
>>>     chirp_users mailing list 
>>>     chirp_users at intrepid.danplanet.com 
>>>     <mailto:chirp_users at intrepid.danplanet.com> 
>>>     http://intrepid.danplanet.com/mailman/listinfo/chirp_users 
>>>     To unsubscribe, send an email to 
>>>     chirp_users-unsubscribe at intrepid.danplanet.com 
>>>     <mailto:chirp_users-unsubscribe at intrepid.danplanet.com> 
>>> 
>>>     _______________________________________________ 
>>>     chirp_users mailing list 
>>>     chirp_users at intrepid.danplanet.com 
>>>     <mailto:chirp_users at intrepid.danplanet.com> 
>>>     http://intrepid.danplanet.com/mailman/listinfo/chirp_users 
>>>     To unsubscribe, send an email to 
>>>     chirp_users-unsubscribe at intrepid.danplanet.com 
>>>     <mailto:chirp_users-unsubscribe at intrepid.danplanet.com> 
>>> 
>>> 
>>> 
>>> _______________________________________________ 
>>> chirp_users mailing list 
>>> chirp_users at intrepid.danplanet.com 
>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users 
>>> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
> 
> 
> 
> I am having the same problem as Ray, but also with my TH 9800. The TYT software can't see
> the radio either. So I don't think it is the plug on the Baofeng cable in my case.
> 
> Thanks for any help...
> 
> 73
> --Rodger
> KK6OPW
> 
>> On 11/5/2015 10:53 AM, Gary Runningbear wrote:
>> Hi Dave, I don't believe there will be a need to be concerned with the port
>> number if the prolific 2303 driver is downloaded and installed. when I did
>> that it immediately recognized the circuitry in the patch cord.
>> On Nov 5, 2015 1:51 PM, "dmdfacp at gmail.com" <dmdfacp at gmail.com> wrote:
>> 
>>> How about your serial port ?  I just jumped in, so forgive me if I'm
>>> redundant.
>>> If you do not know which port is being used, unplug your USB-to-radio
>>> cable at the computer end. Re-plug it and watch for a small notice
>>> specifying the port to which the computer connected it. Verify that CHIRP
>>> is looking at the correct port.
>>> I just went through this, within the past half hour. Good luck. I'm a
>>> newbie, here, too.
>>> Dave
>>> 
>>> Sent from my iPhone
>>> DSP
>>> 
>>> On Nov 5, 2015, at 1:08 PM, Ray Nelson via chirp_users <
>>> chirp_users at intrepid.danplanet.com> wrote:
>>> 
>>> I've downloaded the software & installed. I keep getting error message the
>>> radio is not connected. What am I doing wrong?
>>> 
>>> Sent from my iPad
>>> _______________________________________________
>>> chirp_users mailing list
>>> chirp_users at intrepid.danplanet.com
>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>> To unsubscribe, send an email to
>>> chirp_users-unsubscribe at intrepid.danplanet.com
>>> 
>>> _______________________________________________
>>> chirp_users mailing list
>>> chirp_users at intrepid.danplanet.com
>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>> To unsubscribe, send an email to
>>> chirp_users-unsubscribe at intrepid.danplanet.com
>>> 
>>> 
>>> 
>>> Hi Dave, I don't believe there will be a need to be concerned with the port number if the prolific 2303 driver is downloaded and installed. when I did that it immediately recognized the circuitry in the patch cord.
>>> 
>>>> On Nov 5, 2015 1:51 PM, "dmdfacp at gmail.com" <dmdfacp at gmail.com> wrote:
>>>> How about your serial port ?  I just jumped in, so forgive me if I'm redundant.  
>>>> If you do not know which port is being used, unplug your USB-to-radio cable at the computer end. Re-plug it and watch for a small notice specifying the port to which the computer connected it. Verify that CHIRP is looking at the correct port.
>>>> I just went through this, within the past half hour. Good luck. I'm a newbie, here, too. 
>>>> Dave
>>>> 
>>>> Sent from my iPhone 
>>>> DSP
>>>> 
>>>> On Nov 5, 2015, at 1:08 PM, Ray Nelson via chirp_users <chirp_users at intrepid.danplanet.com> wrote:
>>>> 
>>>> I've downloaded the software & installed. I keep getting error message the radio is not connected. What am I doing wrong? 
>>>> 
>>>> Sent from my iPad
>>>> _______________________________________________
>>>> chirp_users mailing list
>>>> chirp_users at intrepid.danplanet.com
>>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>>> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
>>>> 
>>>> _______________________________________________
>>>> chirp_users mailing list
>>>> chirp_users at intrepid.danplanet.com
>>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>>> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
>>> 
>>> 
>>> _______________________________________________
>>> chirp_users mailing list
>>> chirp_users at intrepid.danplanet.com
>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
> 
> 
> 
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com

_______________________________________________
chirp_users mailing list
chirp_users at intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20151105/5490a5e9/attachment.html 