[chirp_users] Radio Not Communicating With Laptop

[Rodger Hess]

I rolled back my Prolific driver to version 3.2.0.0 and now all is well.

73
--Rodger
KK6OPW

On 11/5/2015 11:35 AM, Rodger Hess wrote:
> I am having the same problem as Ray, but also with my TH 9800. The TYT 
> software can't see
> the radio either. So I don't think it is the plug on the Baofeng cable 
> in my case.
>
> Thanks for any help...
>
> 73
> --Rodger
> KK6OPW
>
> On 11/5/2015 10:53 AM, Gary Runningbear wrote:
>> Hi Dave, I don't believe there will be a need to be concerned with 
>> the port
>> number if the prolific 2303 driver is downloaded and installed. when 
>> I did
>> that it immediately recognized the circuitry in the patch cord.
>> On Nov 5, 2015 1:51 PM, "dmdfacp at gmail.com" <dmdfacp at gmail.com> wrote:
>>
>>> How about your serial port ?  I just jumped in, so forgive me if I'm
>>> redundant.
>>> If you do not know which port is being used, unplug your USB-to-radio
>>> cable at the computer end. Re-plug it and watch for a small notice
>>> specifying the port to which the computer connected it. Verify that 
>>> CHIRP
>>> is looking at the correct port.
>>> I just went through this, within the past half hour. Good luck. I'm a
>>> newbie, here, too.
>>> Dave
>>>
>>> Sent from my iPhone
>>> DSP
>>>
>>> On Nov 5, 2015, at 1:08 PM, Ray Nelson via chirp_users <
>>> chirp_users at intrepid.danplanet.com> wrote:
>>>
>>> I've downloaded the software & installed. I keep getting error 
>>> message the
>>> radio is not connected. What am I doing wrong?
>>>
>>> Sent from my iPad
>>> _______________________________________________
>>> chirp_users mailing list
>>> chirp_users at intrepid.danplanet.com
>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>> To unsubscribe, send an email to
>>> chirp_users-unsubscribe at intrepid.danplanet.com
>>>
>>> _______________________________________________
>>> chirp_users mailing list
>>> chirp_users at intrepid.danplanet.com
>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>> To unsubscribe, send an email to
>>> chirp_users-unsubscribe at intrepid.danplanet.com
>>>
>>>
>>>
>>> Hi Dave, I don't believe there will be a need to be concerned with 
>>> the port number if the prolific 2303 driver is downloaded and 
>>> installed. when I did that it immediately recognized the circuitry 
>>> in the patch cord.
>>>
>>> On Nov 5, 2015 1:51 PM, "dmdfacp at gmail.com 
>>> <mailto:dmdfacp at gmail.com>" <dmdfacp at gmail.com 
>>> <mailto:dmdfacp at gmail.com>> wrote:
>>>
>>>     How about your serial port ?  I just jumped in, so forgive me if
>>>     I'm redundant.
>>>     If you do not know which port is being used, unplug your
>>>     USB-to-radio cable at the computer end. Re-plug it and watch for
>>>     a small notice specifying the port to which the computer
>>>     connected it. Verify that CHIRP is looking at the correct port.
>>>     I just went through this, within the past half hour. Good luck.
>>>     I'm a newbie, here, too.
>>>     Dave
>>>
>>>     Sent from my iPhone
>>>     DSP
>>>
>>>     On Nov 5, 2015, at 1:08 PM, Ray Nelson via chirp_users
>>>     <chirp_users at intrepid.danplanet.com
>>>     <mailto:chirp_users at intrepid.danplanet.com>> wrote:
>>>
>>>     I've downloaded the software & installed. I keep getting error
>>>     message the radio is not connected. What am I doing wrong?
>>>
>>>     Sent from my iPad
>>>     _______________________________________________
>>>     chirp_users mailing list
>>>     chirp_users at intrepid.danplanet.com
>>>     <mailto:chirp_users at intrepid.danplanet.com>
>>>     http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>>     To unsubscribe, send an email to
>>>     chirp_users-unsubscribe at intrepid.danplanet.com
>>> <mailto:chirp_users-unsubscribe at intrepid.danplanet.com>
>>>
>>>     _______________________________________________
>>>     chirp_users mailing list
>>>     chirp_users at intrepid.danplanet.com
>>>     <mailto:chirp_users at intrepid.danplanet.com>
>>>     http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>>     To unsubscribe, send an email to
>>>     chirp_users-unsubscribe at intrepid.danplanet.com
>>> <mailto:chirp_users-unsubscribe at intrepid.danplanet.com>
>>>
>>>
>>>
>>> _______________________________________________
>>> chirp_users mailing list
>>> chirp_users at intrepid.danplanet.com
>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>> To unsubscribe, send an email to 
>>> chirp_users-unsubscribe at intrepid.danplanet.com
>
>
>
> I am having the same problem as Ray, but also with my TH 9800. The TYT 
> software can't see
> the radio either. So I don't think it is the plug on the Baofeng cable 
> in my case.
>
> Thanks for any help...
>
> 73
> --Rodger
> KK6OPW
>
> On 11/5/2015 10:53 AM, Gary Runningbear wrote:
>> Hi Dave, I don't believe there will be a need to be concerned with the port
>> number if the prolific 2303 driver is downloaded and installed. when I did
>> that it immediately recognized the circuitry in the patch cord.
>> On Nov 5, 2015 1:51 PM,"dmdfacp at gmail.com"  <dmdfacp at gmail.com>  wrote:
>>
>>> How about your serial port ?  I just jumped in, so forgive me if I'm
>>> redundant.
>>> If you do not know which port is being used, unplug your USB-to-radio
>>> cable at the computer end. Re-plug it and watch for a small notice
>>> specifying the port to which the computer connected it. Verify that CHIRP
>>> is looking at the correct port.
>>> I just went through this, within the past half hour. Good luck. I'm a
>>> newbie, here, too.
>>> Dave
>>>
>>> Sent from my iPhone
>>> DSP
>>>
>>> On Nov 5, 2015, at 1:08 PM, Ray Nelson via chirp_users <
>>> chirp_users at intrepid.danplanet.com> wrote:
>>>
>>> I've downloaded the software & installed. I keep getting error message the
>>> radio is not connected. What am I doing wrong?
>>>
>>> Sent from my iPad
>>> _______________________________________________
>>> chirp_users mailing list
>>> chirp_users at intrepid.danplanet.com
>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>> To unsubscribe, send an email to
>>> chirp_users-unsubscribe at intrepid.danplanet.com
>>>
>>> _______________________________________________
>>> chirp_users mailing list
>>> chirp_users at intrepid.danplanet.com
>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>> To unsubscribe, send an email to
>>> chirp_users-unsubscribe at intrepid.danplanet.com
>>>
>>>
>>>
>>> Hi Dave, I don't believe there will be a need to be concerned with 
>>> the port number if the prolific 2303 driver is downloaded and 
>>> installed. when I did that it immediately recognized the circuitry 
>>> in the patch cord.
>>>
>>> On Nov 5, 2015 1:51 PM, "dmdfacp at gmail.com" <dmdfacp at gmail.com 
>>> <mailto:dmdfacp at gmail.com>> wrote:
>>>
>>>     How about your serial port ?  I just jumped in, so forgive me if
>>>     I'm redundant.
>>>     If you do not know which port is being used, unplug your
>>>     USB-to-radio cable at the computer end. Re-plug it and watch for
>>>     a small notice specifying the port to which the computer
>>>     connected it. Verify that CHIRP is looking at the correct port.
>>>     I just went through this, within the past half hour. Good luck.
>>>     I'm a newbie, here, too.
>>>     Dave
>>>
>>>     Sent from my iPhone
>>>     DSP
>>>
>>>     On Nov 5, 2015, at 1:08 PM, Ray Nelson via chirp_users
>>>     <chirp_users at intrepid.danplanet.com
>>>     <mailto:chirp_users at intrepid.danplanet.com>> wrote:
>>>
>>>     I've downloaded the software & installed. I keep getting error
>>>     message the radio is not connected. What am I doing wrong?
>>>
>>>     Sent from my iPad
>>>     _______________________________________________
>>>     chirp_users mailing list
>>>     chirp_users at intrepid.danplanet.com
>>>     <mailto:chirp_users at intrepid.danplanet.com>
>>>     http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>>     To unsubscribe, send an email to
>>>     chirp_users-unsubscribe at intrepid.danplanet.com
>>>
>>>     _______________________________________________
>>>     chirp_users mailing list
>>>     chirp_users at intrepid.danplanet.com
>>>     <mailto:chirp_users at intrepid.danplanet.com>
>>>     http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>>     To unsubscribe, send an email to
>>>     chirp_users-unsubscribe at intrepid.danplanet.com
>>>     <mailto:chirp_users-unsubscribe at intrepid.danplanet.com>
>>>
>>>
>>>
>>> _______________________________________________
>>> chirp_users mailing list
>>> chirp_users at intrepid.danplanet.com
>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>> To unsubscribe, send an email tochirp_users-unsubscribe at intrepid.danplanet.com
>
>
>
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20151105/46cc4e96/attachment.html