[chirp_users] Unable to upload to VX-5R

[Jean-Paul Louis]

The FTDI driver will not be selected when you plug your cable. You need also the Prolific driver. Try installing the 1.6 first.

Jean-Paul

> On Apr 21, 2018, at 3:54 PM, Fuchs Ira <irafuchs at gmail.com> wrote:
> 
> I tried downloading the latest FTDI driver (FTDIUSBSerialDriver_v2_4_2), installed it, and rebooted OSX. There was no change to the USB serial driver info in system report. So, I was already running this driver, or I need to do something else to have it use this driver, or…? Also the FTDI site shows 2 different types of drivers are available, the one I used and this one (D2XX1.4.4).  What I find interesting is the one direction from the radio works flawlessly and te other direction (to the radio) fails after it is theoretically 3/4 done. Usually drivers fail in more definitive ways but clearly others are able to use Chirp bi-directionally with the VX-5R. By the way, for what it is worth, I have no trouble with upload and download to a Btech UV-5R. Of course that it is a different cable.
> 
>> On Apr 21, 2018, at 2:41 PM, Jean-Paul Louis via chirp_users <chirp_users at intrepid.danplanet.com> wrote:
>> 
>> OK,
>> Now the only thing left is the USB_Serial driver.
>> Mine shows up on the system info app as
>> 
>> FT232R USB UART:
>> 
>> Product ID:	0x6001
>> Vendor ID:	0x0403  (Future Technology Devices International Limited)
>> Version:	6.00
>> Serial Number:	AI03E0C2
>> Speed:	Up to 12 Mb/sec
>> Manufacturer:	FTDI
>> Location ID:	0x14100000 / 20
>> Current Available (mA):	500
>> Current Required (mA):	90
>> Extra Operating Current (mA):	0
>> 
>> So I loaded the latest FTDI driver from the FTDI website, and everything has been fine since.
>> 
>> A friend of mine had a cheap interface with a chip from Prolific, and I had a heck of a time to find the right driver, but I made it work eventually when I used a driver from Prolific website.
>> 
>> So your mileage might vary.
>> 
>> Good luck,
>> Jean-Paul
>> N1JPL
>> 
>> 
>>> On Apr 20, 2018, at 11:24 PM, Fuchs Ira <irafuchs at gmail.com> wrote:
>>> 
>>> The volume is at max and it still dies about 3/4 of the way to completing the upload.
>>> 
>>> As far as trying "another Chirp program" due to a driver issue, I’m not sure where that would be found or what to try.
>>> 
>>> 
>>>> On Apr 20, 2018, at 8:43 PM, Jean-Paul Louis via chirp_users <chirp_users at intrepid.danplanet.com> wrote:
>>>> 
>>>> Ira,
>>>> Do you have the volume up to the max on the radio? I have seen upload fails when volume is too low
>>>> 
>>>> Jean-Paul
>>>> 
>>>> 
>>>>> On Apr 20, 2018, at 2:42 PM, Ira Fuchs <irafuchs at gmail.com> wrote:
>>>>> 
>>>>> It’s
>>>> 
>>>> _______________________________________________
>>>> chirp_users mailing list
>>>> chirp_users at intrepid.danplanet.com
>>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>>> This message was sent to Ira Fuchs at irafuchs at gmail.com
>>>> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
>>> 
>>> _______________________________________________
>>> chirp_users mailing list
>>> chirp_users at intrepid.danplanet.com
>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>> This message was sent to Jean-Paul Louis at louijp at yahoo.com
>>> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
>> 
>> _______________________________________________
>> chirp_users mailing list
>> chirp_users at intrepid.danplanet.com
>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>> This message was sent to Ira Fuchs at irafuchs at gmail.com
>> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
> 
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to Jean-Paul Louis at louijp at yahoo.com
> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com