[chirp_users] Yaesu FT-7900R driver needed. I think :)

Mark Fernandez apple2gs at sbcglobal.net
Mon Mar 11 18:01:56 PDT 2013


You guys are the GREATEST!  Thank you all so much. 

-Mark

Sent from M. Fernandez

On Mar 11, 2013, at 8:59 PM, Mark Fernandez <apple2gs at sbcglobal.net> wrote:

> Ah-haaaaa. I got it!!
> I had to get it in RX mode to upload. :D
> 
> 
> -mark
> 
> Sent from M. Fernandez
> 
> On Mar 11, 2013, at 8:46 PM, Apple //GS <apple2gs at sbcglobal.net> wrote:
> 
>> Okay.  First thank you and Dan so much!!  :)
>> 
>> Well, I got CHIRP to see the radio, after following what you said (I feel soooooo dumb, I should have re-read that stuff)  thanks.
>> 
>> I got CHIRp to download from the 7900.
>> I then input some channels from the Repeater Book input.
>> 
>> The channels went in to the CHIRP spread sheet.
>> 
>> I then tried to upload back to the radio……………..
>> 
>> THis it what it says now:
>> 
>> Radio did not ack block at 0
>> 
>> -Mark
>> 
>> 
>> 
>> 
>> On Mar 11, 2013, at 7:10 PM, Tom Hayward <esarfl at gmail.com> wrote:
>> 
>>> On Mon, Mar 11, 2013 at 3:50 PM, Apple //GS <apple2gs at sbcglobal.net> wrote:
>>>> I turned the radio on while holding the "MHz/PRI" button.  Then turned the dial to F-7 CLONE
>>>> 
>>>> Should I do something else?
>>> 
>>> You missed a step. Page 66 of your manual:
>>> 
>>> To clone from one transceiver to a computer, use the following procedure:
>>> 1. Insert the Cloning Cable into the DATA jack of the transceiver.
>>> 2. Turn transceiver off, then press and hold in the [MHz(PRI)] key
>>> while turning the power on again.
>>> 3. Rotate the DIAL knob on each radio to select (F-7 CLONE), then
>>> press and hold in the [BAND(SET)] key. The display will disappear for
>>> a moment, then the “CLONE” notation will appear on the display.
>>> 4. In Chirp, select Download From Radio
>>> 5. Now, on the “Source” radio, press the [V/M(MW)] key. The “- - TX -
>>> -” indicator will appear on the display, and the cloning data transfer
>>> will immediately begin.
>>> 6. If there is a problem during the cloning process, “ERROR” will be
>>> displayed. Check your cable connections, and try again.
>>> 7. If cloning was successful, “CLONE” will reappear the radio display.
>>> Chirp will present your memory channels in a spreadsheet format.
>>> 
>>> Tom KD7LXL
>>> _______________________________________________
>>> chirp_users mailing list
>>> chirp_users at intrepid.danplanet.com
>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>> 
>> _______________________________________________
>> chirp_users mailing list
>> chirp_users at intrepid.danplanet.com
>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users


More information about the chirp_users mailing list