<div dir="auto">Morning <div dir="auto"><br></div><div dir="auto">Thank you I will try to feed it into chirp later today Thank you,still playing around with Chirp,not a expert.</div><div dir="auto"><br></div><div dir="auto">Thank you</div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Wed, Jan 31, 2024, 22:48 Jim Unroe <<a href="mailto:rock.unroe@gmail.com">rock.unroe@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Hi Bennie,<br>
<br>
On Wed, Jan 31, 2024 at 5:40 AM Bennie Potgieter<br>
<<a href="mailto:potgieterbarends4@gmail.com" target="_blank" rel="noreferrer">potgieterbarends4@gmail.com</a>> wrote:<br>
><br>
> Gooday<br>
><br>
> I used this unit to get a a channel from a radio on a repeater is this the transmit or receive channel and the CT tone is positive I think how do I get te other channel end how do I feed it Manuel and with Chirp into my UV5R?<br>
<br>
First you have to realize that the frequency transmitted from the<br>
source radio is probably not going to be perfect. And second, the<br>
cheap rike frequency counter (I have one, too) is probably not going<br>
to be 100% accurate. Knowing this, the actual frequency would most<br>
likely be 464.375.<br>
<br>
Since the frequency captured is from a transmitting radio, the<br>
frequency is the transmit frequency of the user (the repeater's RX<br>
frequency). In the only document that I have been able to find with<br>
464.375 being used as a repeater frequency, the repeater's TX<br>
frequency is 5.000 MHz (which is common for UHF repeaters in the USA).<br>
<br>
It is obvious that a 118.8 Hz CTCSS tone is being transmitted to the<br>
repeater. It would make sense to assume that this is required to<br>
access the repeater. It is possible that the repeater doesn't require<br>
a tone, but in that case, transmitting one anyway won't hurt anything.<br>
<br>
If the repeater doesn't require a tone and/or doesn't transmit one<br>
back (or transmits a different CTCSS tone or even a DCS code), then<br>
copy-and-pasting the following into CHIRP-next should work.<br>
[454.375000/+5.000/118.8]<br>
<br>
If the repeater does transmit a 118.8 CTCSS tone back to the user then<br>
copy-and-pasting the following into CHIRP-next should work.<br>
[454.375000/+5.000/118.8/118.8]<br>
<br>
I would copy-and-paste both into CHIRP creating 2 channels that you<br>
can test with.<br>
<br>
Just note that depending on where in the world you are located, it may<br>
not be legal for you to transmit with your radio on that frequency so<br>
any transmission that you may make is solely your responsibility.<br>
<br>
Jim KC9HI<br>
_______________________________________________<br>
chirp_users mailing list<br>
<a href="mailto:chirp_users@intrepid.danplanet.com" target="_blank" rel="noreferrer">chirp_users@intrepid.danplanet.com</a><br>
<a href="http://intrepid.danplanet.com/mailman/listinfo/chirp_users" rel="noreferrer noreferrer" target="_blank">http://intrepid.danplanet.com/mailman/listinfo/chirp_users</a><br>
This message was sent to <a href="mailto:potgieterbarends4@gmail.com" target="_blank" rel="noreferrer">potgieterbarends4@gmail.com</a> at <a href="mailto:potgieterbarends4@gmail.com" target="_blank" rel="noreferrer">potgieterbarends4@gmail.com</a><br>
To unsubscribe, send an email to <a href="mailto:chirp_users-unsubscribe@intrepid.danplanet.com" target="_blank" rel="noreferrer">chirp_users-unsubscribe@intrepid.danplanet.com</a><br>
To report this email as off-topic, please email <a href="mailto:chirp_users-owner@intrepid.danplanet.com" target="_blank" rel="noreferrer">chirp_users-owner@intrepid.danplanet.com</a><br>
Searchable archive: <a href="https://www.mail-archive.com/chirp_users@intrepid.danplanet.com" rel="noreferrer noreferrer" target="_blank">https://www.mail-archive.com/chirp_users@intrepid.danplanet.com</a></blockquote></div>