<div>Oops, forgot to say, it should work properly, just not show it. <br/>
<br/>
D. Buss<br/>
KD9EBR<br/><br/>-----Original Message-----<br/>From: Gary Runningbear <runningbear2000@gmail.com><br/>To: Discussion of CHIRP <chirp_users@intrepid.danplanet.com><br/>Sent: Thu, 05 Nov 2015 11:14<br/>Subject: Re: [chirp_users] Freq entry<br/><br/></div><p dir="ltr">Just found another problem. I enter a frequency a ct tone and an offset and save to a channel. This is in the VFO of Courts. then I go to channel mode and pull up that channel and find that the CT tone and the offset have not carried over. It is acting like a simplex frequency. did I do something wrong or miss something?</p>
<div class="gmail_quote">On Nov 5, 2015 11:28 AM, "Gary Runningbear" <<a href="mailto:runningbear2000@gmail.com">runningbear2000@gmail.com</a>> wrote:<br type="attribution"><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><p dir="ltr">Ok. I just figured out how to add up to 5 decimal places. many thanks</p>
<div class="gmail_quote">On Nov 5, 2015 11:23 AM, "Jim Unroe" <<a href="mailto:rock.unroe@gmail.com" target="_blank">rock.unroe@gmail.com</a>> wrote:<br type="attribution"><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">On Thu, Nov 5, 2015 at 11:02 AM, Gary Runningbear<br>
<<a href="mailto:runningbear2000@gmail.com" target="_blank">runningbear2000@gmail.com</a>> wrote:<br>
> In the UV 82L, when adding frequencies that have four to five digits to the<br>
> right of the decimal point how do you get the last one or two digits in<br>
> there?<br>
><br>
<br>
You just type it into the Frequency cell of the memory spreadsheet editor.<br>
<br>
If you are talking about entering the frequency into the VFO using the<br>
keypad (which has nothing to do with CHIRP), you do the following:<br>
<br>
1 set menu 1 (STEP) to a value that is compatible with the frequency<br>
that you want to enter<br>
2 key in the 1st 6 digits of the frequency<br>
3 press the [^] up arrow key once<br>
<br>
For example if you want to listen to FRS channel, 462.5625 MHz<br>
<br>
1 Set STEP to 2.5KHZ, 6.25KHZ or 12.5KHZ<br>
2 Key in 462562 (after entering the last 2, the frequency will be<br>
rounded off to the 1st STEP compatible frequency below the desired<br>
frequency)<br>
3 Press the [^] up arrow key once (the display will read "462.562"<br>
followed by a very small 5)<br>
<br>
Jim KC9HI<br>
_______________________________________________<br>
chirp_users mailing list<br>
<a href="mailto:chirp_users@intrepid.danplanet.com" target="_blank">chirp_users@intrepid.danplanet.com</a><br>
<a href="http://intrepid.danplanet.com/mailman/listinfo/chirp_users" rel="noreferrer" target="_blank">http://intrepid.danplanet.com/mailman/listinfo/chirp_users</a><br>
To unsubscribe, send an email to <a href="mailto:chirp_users-unsubscribe@intrepid.danplanet.com" target="_blank">chirp_users-unsubscribe@intrepid.danplanet.com</a><br>
</blockquote></div>
</blockquote></div>