<div dir="ltr"><div>Issue:</div><div>Cannot get a driver to function on my w8.1 machine using<br></div><div>same cable (with FTDI chip), Win_Driver_Prolific_3_2_0_0</div><div>and UV-3R transceiver software that all works FINE on my </div><div>big 64b W7 machine incl Chirp.</div><div><br></div><div>Any suggestions on how to solve the W8.1 problems????</div><div><br></div><div>The W8.1 Dell Laptop has 3gb ram, 500gb HD and otherwise</div><div>runs flawlessly.</div><div><br></div><div>73</div></div><div class="gmail_extra"><br><div class="gmail_quote">On Sun, Jul 19, 2015 at 8:43 PM, Pavel Milanes Costa <span dir="ltr"><<a href="mailto:co7wt@frcuba.co.cu" target="_blank">co7wt@frcuba.co.cu</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><br>
El 19/07/15 a las 20:21, Jim Unroe escribió:<br>
<div><div class="h5">> On Sun, Jul 19, 2015 at 11:20 AM, Pavel Milanes Costa<br>
> <<a href="mailto:co7wt@frcuba.co.cu">co7wt@frcuba.co.cu</a>> wrote:<br>
>> Hi, I'm new to the list...<br>
>><br>
>> I was searching the list archives for this, but found no answer, so here<br>
>> it goes...<br>
>><br>
>> The squelch levels for VHF/UHF on the settings > service settings<br>
>> options do work for the Baofeng UV-5R?<br>
>><br>
>> My Baofeng is about 10uV in VHF and ~2.0uV on UHF, so VHF reception is<br>
>> hard, may be it has to do with the SQ level, it has 25 as SQL 0 for VHF<br>
>> and 19 on SQL 0 for UHF.<br>
>><br>
>> So before I play with that values I want to know if this setting will<br>
>> really work with my radio.<br>
>><br>
>> I'm using chirp-daily-20150702 here...<br>
>><br>
>> 73,<br>
>><br>
>> --<br>
>> M.Sc. Pavel Milanes Costa, CO7WT<br>
>> SYSOP Nodo Gateway CO9JAZ<br>
>> Ciudad de Camagüey, Camagüey, Cuba.<br>
>> Cell: (+53) 53-847819<br>
>><br>
>> Este email fue enviado usando packet radio a 9600 baudios<br>
>> This email was sent using Amateur Packet Radio at 9600 baud<br>
><br>
> There is no guarantee that it will work. Feedback shows that it works<br>
> for firmware version BFB291 and newer. The settings won't show up if<br>
> the firmware version is older than this. The improvement seems to vary<br>
> from firmware version to firmware version and model to model.<br>
><br>
> Always save your radio's channels and settings before you start making<br>
> any changes. That way you can always get back to where you started. It<br>
> appears that you have test equipment available. All you have to do is<br>
> change one setting to see if it works. If it doesn't, then change it<br>
> back.<br>
><br>
> Jim KC9HI<br>
<br>
</div></div>Thanks for the answer Tim.<br>
<br>
My firmware is BFB297 N5R-20, so it may work... I will try and get back<br>
to the list to report..<br>
<br>
73<br>
<div class="HOEnZb"><div class="h5"><br>
_______________________________________________<br>
chirp_users mailing list<br>
<a href="mailto:chirp_users@intrepid.danplanet.com">chirp_users@intrepid.danplanet.com</a><br>
<a href="http://intrepid.danplanet.com/mailman/listinfo/chirp_users" rel="noreferrer" target="_blank">http://intrepid.danplanet.com/mailman/listinfo/chirp_users</a><br>
To unsubscribe, send an email to <a href="mailto:chirp_users-unsubscribe@intrepid.danplanet.com">chirp_users-unsubscribe@intrepid.danplanet.com</a></div></div></blockquote></div><br></div>