<html><body><div style="color:#000; background-color:#fff; font-family:HelveticaNeue, Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif;font-size:12pt"><div><span>If you visit here: http://www.miklor.com/uv5r/</span></div><div style="color: rgb(0, 0, 0); font-size: 16px; font-family: HelveticaNeue, 'Helvetica Neue', Helvetica, Arial, 'Lucida Grande', sans-serif; background-color: transparent; font-style: normal;"><span>I think you will get your problems sorted out in</span></div><div style="color: rgb(0, 0, 0); font-size: 16px; font-family: HelveticaNeue, 'Helvetica Neue', Helvetica, Arial, 'Lucida Grande', sans-serif; background-color: transparent; font-style: normal;"><span>short order. Looks like by the driver device your</span></div><div style="color: rgb(0, 0, 0); font-size: 16px; font-family: HelveticaNeue, 'Helvetica Neue', Helvetica, Arial, 'Lucida Grande', sans-serif; background-color: transparent; font-style: normal;"><span>using
a linux OS. There are a few considerations </span></div><div style="color: rgb(0, 0, 0); font-size: 16px; font-family: HelveticaNeue, 'Helvetica Neue', Helvetica, Arial, 'Lucida Grande', sans-serif; background-color: transparent; font-style: normal;"><span>but I think they are covered on the Miklor site. </span></div><div><br></div> <div style="font-family: HelveticaNeue, 'Helvetica Neue', Helvetica, Arial, 'Lucida Grande', sans-serif; font-size: 12pt;"> <div style="font-family: HelveticaNeue, 'Helvetica Neue', Helvetica, Arial, 'Lucida Grande', sans-serif; font-size: 12pt;"> <div dir="ltr"> <hr size="1"> <font size="2" face="Arial"> <b><span style="font-weight:bold;">From:</span></b> Tony Cratz <cratz@hematite.com><br> <b><span style="font-weight: bold;">To:</span></b> chirp_users@intrepid.danplanet.com <br> <b><span style="font-weight: bold;">Sent:</span></b> Wednesday, October 9, 2013 11:13 PM<br> <b><span style="font-weight:
bold;">Subject:</span></b> [chirp_users] Baofeng uv-5r plus not able to read from<br> </font> </div> <div class="y_msg_container"><br>Hello,<br><br> I just purchase a UV-5R+ and was trying to program it. I'm using<br> the chirp-daily respository version.<br><br> USB Cable: : Prolific Technology Inc. pl2303 3-2:1.0: pl2303<br> device: /dev/ttyUSB0<br> UV-5R+ Firmware: BFB297 (as reported via power-on)<br><br> I get the typical unable to connect to radio, but when it is<br> trying to clone I see on the HT the "Welcome...." message and<br> then I get the timeout message.<br><br> As for the cable, it does seem to be full seated. I have<br> pressed and held the plug in to make sure and get the same<br> results.<br><br> First is there a debug mode
I can turn on to capture the hand<br> shake between the computer and the UV-5R+. I figure this would<br> help the list.<br><br><br> Tony<br>_______________________________________________<br>chirp_users mailing list<br><a ymailto="mailto:chirp_users@intrepid.danplanet.com" href="mailto:chirp_users@intrepid.danplanet.com">chirp_users@intrepid.danplanet.com</a><br><a href="http://intrepid.danplanet.com/mailman/listinfo/chirp_users" target="_blank">http://intrepid.danplanet.com/mailman/listinfo/chirp_users</a><br><br><br></div> </div> </div> </div></body></html>