[chirp_users] Add-on Modules/Scripts for Chirp ?

[John Cooley]

Bruce,
   FYI, I run a program called Freescan (under windows) that works well
with my BCD329P2.
I see in the RR site it also runs under Linux, but I don't use Linux much.

ere is a lionk to the page: Freescan Install Under LINUX - The
RadioReference Wiki
<https://wiki.radioreference.com/index.php/Freescan_Install_Under_LINUX>

John Cooley
wb8wbn at arrl.net


On Tue, May 17, 2022 at 9:04 AM Ken Hansen <ken at n2vip.org> wrote:

> I think this would be a big task, as currently CHIRP has no built-in
> support for any scanners from any manufacturer, based on a quick scan of
> the CHIRP homepage:
>
> https://chirp.danplanet.com/projects/chirp/wiki/Home
>
> I am not aware of any publicly-available documentation on how to program a
> Uniden/bearcat scanner, though I suppose there's likely something somewhere.
>
> CHIRP architecture (as far as I can tell from the outside looking in) is
> not setup to handle trunking groups, digital modes, etc.
>
> I appreciate the desire to avoid windows, but the alternative would be
> front panel programming your frequencies into the scanner. I had no problem
> banging in about a hundred frequencies into a simple Whistler desktop
> scanner, but all that entailed was typing in each frequency and saving it
> to memory (no tone, no label, nothing, just frequency they the keypad) -
> your 'fancy' scanner would take a greater effort.
>
> It is a nice looking scanner - it has a nice feature set and covers ham
> bands from 10 meters to 23 cm - and reminds me of a radio shack scanner I
> have, the PRO-2051, but they are not the same. I was able to get the
> required cable and the appropriate windows software to program my scanner,
> I'd encourage you to do the same.
>
> https://www.universal-radio.com/catalog/scanners/0780.html
>
> Maybe ask a windows-running friend to help, programming scanners is, in my
> experience, typically a "one and done" kind of thing, where once
> programmed, they are never touched again (or at least very rarely).
>
> Good luck!
>
> Ken, N2VIP
>
> On May 17, 2022, at 08:18, KB6LWN - Bruce <kb6lwn at qso.com> wrote:
>
> Hello Group,
>
> Just received delivery of a new-old Uniden BC-780XLT
> Trunk Tracker III Scanner, and I'd like to be able to
> program it with my PC (Linux Mint Desktop), and I'm
> wondering if there is a 'module' available for Chirp
> that will allow me to do this.
> Just updated to the latest FlatPak.  (Linux Mint 20.4)
>
> Since I use Linux - I don't have access to run the MS-
> Windows version of the software specifically written
> for this receiver.   Which reminds me 'rigctl' seems to
> read the receiver and I have gotten a list of the cmd-
> capabilities using that tool, if that is needed...
>
> If there is not a module specifically FOR this receiver,
> perhaps I could get a copy of a module for another unit
> that I might be able to modify for my use.
> Anything is better than going back to Windows, or trying
> to get Wine to work under Linux...
> A Linux native (port) is really needed for scanner Ops...
>
> At this point I use Chirp to program my various BTech,
> Bao's, Leixen, and a couple more, and it makes the task
> so much easier.   Hope to do the same with the scanner...
>
>
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to Ken Hansen at ken at n2vip.org
> To unsubscribe, send an email to
> chirp_users-unsubscribe at intrepid.danplanet.com
> To report this email as off-topic, please email
> chirp_users-owner at intrepid.danplanet.com
>
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to wb8wbn at arrl.net at wb8wbn at arrl.net
> To unsubscribe, send an email to
> chirp_users-unsubscribe at intrepid.danplanet.com
> To report this email as off-topic, please email
> chirp_users-owner at intrepid.danplanet.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20220517/1a2b45be/attachment.html