[chirp_users] chirp_users Digest, Vol 152, Issue 12

Dan Brightwell danbrightwell24 at gmail.com
Mon Aug 23 07:12:11 PDT 2021


Remove me from your mailing list.

On Sun, Aug 22, 2021, 3:00 PM <chirp_users-request at intrepid.danplanet.com>
wrote:

> Send chirp_users mailing list submissions to
>         chirp_users at intrepid.danplanet.com
>
> To subscribe or unsubscribe via the World Wide Web, visit
>         http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> or, via email, send a message with subject or body 'help' to
>         chirp_users-request at intrepid.danplanet.com
>
> You can reach the person managing the list at
>         chirp_users-owner at intrepid.danplanet.com
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of chirp_users digest..."
>
>
> Today's Topics:
>
>    1. Re: UV5X Programming issue (White Ranger)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Sat, 21 Aug 2021 14:33:09 -0500
> From: White Ranger <cortchubby20007 at gmail.com>
> Subject: Re: [chirp_users] UV5X Programming issue
> To: Discussion of CHIRP <chirp_users at intrepid.danplanet.com>
> Message-ID:
>         <CAP+N95FGwe=
> VRT21Yd+EiDSjhknL0j_xGhMZqD7PEJXniiT93Q at mail.gmail.com>
> Content-Type: text/plain; charset="utf-8"
>
> Radio should be ON when up or downloading.
> Remove the driver and cable program, reboot PC reload driver
> SHOULD correct issue. If using aftermarket cable check to see contacts are
> CLEAN (*shiny) and fit TIGHTLY into the mike provisioning adapter (Mic
> jack) DO NOT touch ANY buttons while programming. Worst case, prior to
> programming RESET the radio to factory resets then load your amended
> program.
>
> On Thu, Aug 19, 2021 at 2:03 PM Jim Unroe <rock.unroe at gmail.com> wrote:
>
> > Hi Eric,
> >
> > On Thu, Aug 19, 2021 at 12:47 PM Eric Chopin <echopin27 at gmail.com>
> wrote:
> > >
> > > UV5XP....
> > >     However to get CHIRP to see the radio either in the 'Download from
> > radio'
> > >     or 'Upload to radio' ... with the cable plugged in to my PC or my
> > MAC, the
> > >     radio must me switched OFF...then as I select 'Download or upload'
> > as I
> > >     select 'OK' i must immediately switch ON my radio then CHIRP sees
> it
> > and
> > >     proceeds. If I try to 'Download or upload' with the radio already
> > switched
> > >     on I get the message 'The radio did not respond' as CHIRP cannot
> see
> > it
> > >     connected.
> > >     Any suggestions?
> > >     Thanks
> > >     VE7ECJ
> >
> > That sounds like a programming cable/driver issue. Also, to program
> > that radio you must choose...
> >
> > Vendor: Radioddity
> > Model: UV-5G
> >
> > Jim KC9HI
> > _______________________________________________
> > chirp_users mailing list
> > chirp_users at intrepid.danplanet.com
> > http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> > This message was sent to cortchubby20007 at gmail.com at
> > cortchubby20007 at gmail.com
> > To unsubscribe, send an email to
> > chirp_users-unsubscribe at intrepid.danplanet.com
> >
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL:
> http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20210821/b544e8b4/attachment-0001.html
>
> ------------------------------
>
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> To unsubscribe, send an email to
> chirp_users-unsubscribe at intrepid.danplanet.com
>
> End of chirp_users Digest, Vol 152, Issue 12
> ********************************************
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20210823/d1230e8f/attachment.html 


More information about the chirp_users mailing list