[chirp_users] New to ham radios
Glenn K0LNY
Fri Dec 11 11:42:41 PST 2020
Well to be sure, I'd download the driver, and copy/install it to your
computer, and then update the driver for your port that the cable is plugged
into, and browse for that driver you just downloaded.
HTH.
Glenn
----- Original Message -----
From: "James Walker" <jwalker3311 at gmail.com>
To: "Discussion of CHIRP" <chirp_users at intrepid.danplanet.com>
Sent: Friday, December 11, 2020 1:37 PM
Subject: Re: [chirp_users] New to ham radios
Hi,
Do you have any recommendations on what cable to buy that will insure that
it’s not counterfeit. Am I supposed to actually see the words prolific
somewhere none of my ports use that term thanks
Respectively,
> On Dec 11, 2020, at 11:30 AM, Glenn K0LNY <glennervin at cableone.net> wrote:
>
> James,
> Here's a bit from an old message I saved, it may help your situation:
> Glenn
>
> The most common problem is using a programming cable with a
> counterfeit Prolific chip with Windows. If the chip is Prolific (check
> Device Manager) and you are using Windows Vista, 7, 8 or 10, you must
> download, install and select an older Prolific v3.2.0.0 device driver
> before you programming cable will work properly.
>
> Check this page for a link to the driver and instructions for
> selecting it after it is installed. Only install this driver if
> Windows recognizes the chip in your cable as a Prolific type chip.
> http://www.miklor.com/COM/UV_Drivers.php
>
> Jim KC9HI
>
> ----- Original Message -----
> From: "James Walker" <jwalker3311 at gmail.com>
> To: "Discussion of CHIRP" <chirp_users at intrepid.danplanet.com>
> Sent: Friday, December 11, 2020 1:18 PM
> Subject: Re: [chirp_users] New to ham radios
>
>
> Hi,
> Yes I’m using Window I believe it’s Window 10 I’m pretty sure it’s com6 I
> have three USB ports, tried all of them, they all say I’m plugged into
> com6.
> Yes when I’m in device manager I have pulled out the cable and it
> disappears. The cable does not start off as com6 only after I go through
> the
> update. If I don’t update the port, CHIRP will not recognize the cable
> while
> trying to clone. Also when I first insert the cable it has the yellow
> triangles before updating
>
> Respectively,
>
> Sent from my iPhone
>
>> On Dec 11, 2020, at 11:06 AM, Glenn K0LNY <glennervin at cableone.net>
>> wrote:
>>
>> Hi James,
>> Are you using Windows?
>> Are you certain that the cable is Com 6 in your device manager?
>> You can open device manager and then remove the cable to see if a port
>> then
>> disappears.
>> Otherwise, you may need to open the device properties on that com port
>> and
>> select an older driver, Windows may have used the driver it wants to use
>> for
>> your cable.
>> If you are using Linux, select USB at the end of the com port list.
>> Glenn
>> ----- Original Message -----
>> From: "James Walker" <jwalker3311 at gmail.com>
>> To: <chirp_users at intrepid.danplanet.com>
>> Sent: Friday, December 11, 2020 12:56 PM
>> Subject: [chirp_users] New to ham radios
>>
>>
>>
>> Good morning,
>>
>> I bought a set of Baofeng UV-82hp radios a few weeks ago since than I
>> have
>> not been able to program them. I tried two different cables so far the
>> one
>> that came with the radios and one that I bought from Amazon, the Amazon
>> cable says it’s FTDI, it does flash and recognize my radios but I get an
>> error message while trying to clone says that the radio can’t be
>> Recognized
>> by com port 6. I’ve tried to update, install, reinstall the ports abound
>> twenty times. I have no idea what I’m doing wrong. I’m going to try
>> another
>> cable any Sunday would be great!
>>
>> Respectively,
>> _______________________________________________
>> chirp_users mailing list
>> chirp_users at intrepid.danplanet.com
>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>> This message was sent to Glenn at glennervin at cableone.net
>> To unsubscribe, send an email to
>> chirp_users-unsubscribe at intrepid.danplanet.com
>>
>> _______________________________________________
>> chirp_users mailing list
>> chirp_users at intrepid.danplanet.com
>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>> This message was sent to James Walker at jwalker3311 at gmail.com
>> To unsubscribe, send an email to
>> chirp_users-unsubscribe at intrepid.danplanet.com
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to Glenn at glennervin at cableone.net
> To unsubscribe, send an email to
> chirp_users-unsubscribe at intrepid.danplanet.com
>
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to James Walker at jwalker3311 at gmail.com
> To unsubscribe, send an email to
> chirp_users-unsubscribe at intrepid.danplanet.com
_______________________________________________
chirp_users mailing list
chirp_users at intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
This message was sent to Glenn at glennervin at cableone.net
To unsubscribe, send an email to
chirp_users-unsubscribe at intrepid.danplanet.com
More information about the chirp_users
mailing list