[chirp_users] Programming Yaesu Radios using CHIRP

Chuck Hast kp4djt at gmail.com
Wed Apr 3 19:02:35 PDT 2019


Also do not forget it runs on the major platforms, i.e. It started out on
Linux and is of course available for
Windows (as you have presented) and Mac. I believe it will also run under
BSD.

A lot of us like to run it on a Raspberry Pi.

On Tue, Apr 2, 2019 at 6:57 PM Amnon Zohar <amnon.zohar at gmail.com> wrote:

> remark for your presentation
> the cheap cables with clone prolific chips works fine with the older
> driver version 3.2.0.0
>
> a good source for technical staff  can be found at www.miklor.com (the
> bible ofradios)
> you can download that driver there....
>
> ‫בתאריך יום ג׳, 2 באפר׳ 2019 ב-23:44 מאת ‪Larry Lovell‬‏ <‪
> larry.lovell76 at gmail.com‬‏>:‬
>
>> I wish to thank all of you for your findings on the Yaesu radios.
>> I am giving a presentation on CHIRP to our local (Eastern Idaho) HAMs
>> tonight.
>> If you are interested, the PDF of my presentation is located at:
>> http://www.qrvtronics.com/CatHAM_Radio/files/UsingCHIRPorOtherSoftware.pdf
>>
>>
>> On Thu, Mar 28, 2019 at 10:36 PM <chirp.cordless at xoxy.net> wrote:
>>
>>> Well there's some truth there, but what truth I'm aware
>>> of should not scare anyone off from using chirp with Yaesus.
>>>
>>> Back in early 2014 I was doing some chirp code development
>>> on FT-60s, fixing some bugs and with the eventual goal of
>>> adding "Settings" control. Someone else has since done that.
>>>
>>> Part of that process is mapping the memory by twiddling bits
>>> in the image, uploading to the radio, and seeing through the
>>> radio's button interface what changed. It went pretty smoothly
>>> for a while, then I managed to brick *TWO* FT-60s. One of
>>> which was repaired by sending it to the factory to replace
>>> an eprom.
>>>
>>> I'm not going to add any further detail here, my investigation
>>> was pretty thoroughly documented in a thread on the chirp_devel
>>> mail list with subject "How to brick an FT-60" starting 3/22/14.
>>> See also Bug #1547: [FT-60] Chirp should check parity on download.
>>>
>>> But normal use of chirp to program radios doesn't do this. The
>>> user interface only lets you make limited, well understood
>>> changes to the radio image bitmap. I still do that with mine.
>>>
>>> -dan
>>>
>>> > Date: Wed, 27 Mar 2019 22:05:06 -0600
>>> > From: Larry Lovell <larry.lovell76 at gmail.com>
>>> > Subject: [chirp_users] Programming Yaesu Radios using CHIRP
>>> > To: Discussion of CHIRP <chirp_users at intrepid.danplanet.com>
>>> >
>>> > Has anyone had a problem programming a Yaesu radio with CHIRP?
>>> > Someone mentioned that their Yaesu was damaged and had to be sent to
>>> the
>>> > factory because CHIRP had overwritten some code controlling the
>>> processor.
>>> > It also had to be re-flashed.
>>> > Since I don't fully understand how CHIRP works this doesn't make sense
>>> to
>>> > me, but knowing manufacturing companies, they may share Channel Memory
>>> with
>>> > processor memory and not think much about it.
>>> > Thanks for your information.
>>>
>>>
>>> _______________________________________________
>>> chirp_users mailing list
>>> chirp_users at intrepid.danplanet.com
>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>> This message was sent to Larry Lovell at larry.lovell76 at gmail.com
>>> To unsubscribe, send an email to
>>> chirp_users-unsubscribe at intrepid.danplanet.com
>>>
>>
>>
>> --
>> Larry Lovell
>> 73's N7RGW
>> http://QRVTronics.com <http://qrvtronics.com>
>> Cell: 214-697-1729
>> _______________________________________________
>> chirp_users mailing list
>> chirp_users at intrepid.danplanet.com
>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>> This message was sent to amnon at amnon.zohar at gmail.com
>> To unsubscribe, send an email to
>> chirp_users-unsubscribe at intrepid.danplanet.com
>
>
>
> --
> Amnon
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to Chuck Hast at kp4djt at gmail.com
> To unsubscribe, send an email to
> chirp_users-unsubscribe at intrepid.danplanet.com



-- 
Chirp + Editcp + MD380Tools on Linux
Celestial!!!
Chuck -- KP4DJT
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20190403/ba2d2e97/attachment-0002.html 


More information about the chirp_users mailing list