[chirp_users] chirp_users Digest, Vol 101, Issue 20
Glenn At Home
Mon May 22 19:59:26 PDT 2017
I had a brainstorm today...
Windows 10, 64 bit version, allows for installing bash, in fact, it is a
Microsoft version of Linux.
You can install Linux programs too.
I'd be willing to bet that Chirp in the CLI would work in that environment.
And then Windows 10 folks could have a better experience.
Glenn
----- Original Message -----
From: "roland kelts via chirp_users" <chirp_users at intrepid.danplanet.com>
To: <chirp_users at intrepid.danplanet.com>
Sent: Monday, May 22, 2017 9:20 PM
Subject: Re: [chirp_users] chirp_users Digest, Vol 101, Issue 20
people seem to have all kinds of problems with windows 10 maybe the whole
system for that o.s. needs to be rewritten i couldn't get chirp to work at
all wouldn't even load . Solution i found and old abandoned computer (dell)
with an earlier os and now everything works!!!
--------------------------------------------
On Sun, 5/21/17, <chirp_users-request at intrepid.danplanet.com> wrote:
Subject: chirp_users Digest, Vol 101, Issue 20
To: chirp_users at intrepid.danplanet.com
Date: Sunday, May 21, 2017, 12:00 PM
Send chirp_users mailing list submissions to
chirp_users at intrepid.danplanet.com
To subscribe or unsubscribe via the
World Wide Web, visit
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
or, via email, send a message with
subject or body 'help' to
chirp_users-request at intrepid.danplanet.com
You can reach the person managing the
list at
chirp_users-owner at intrepid.danplanet.com
When replying, please edit your Subject
line so it is more specific
than "Re: Contents of chirp_users
digest..."
Today's Topics:
1. Re: Cannot read Baofeng
BF-888S (Jim Unroe)
2. Re: Leixen VV-898E on MacOS?
(was: ...daily-20170501
repeatable crash)
(Rich Baker)
3. Re: Cannot read Baofeng
BF-888S (Rich Baker)
4. Re: Leixen VV-898E on MacOS?
(was: ...daily-20170501
repeatable crash)
(Jardy Dawson)
5. Re: Cannot read Baofeng
BF-888S (Jardy Dawson)
6. Re: Cannot read Baofeng
BF-888S (Jim McCorison)
7. Re: Leixen VV-898E on MacOS?
(was: ...daily-20170501
repeatable crash)
(Rich Baker)
8. Re: Cannot read Baofeng
BF-888S (Rich Baker)
9. Re: Cannot read Baofeng
BF-888S (Jim McCorison)
10. FT2D (NNN Wx)
11. Re: chirp_users Digest, Vol
101, Issue 19 (Bob Decker)
12. Re: chirp_users Digest, Vol
101, Issue 19 (Carrie Jackson)
13. Re: Cannot read Baofeng
BF-888S (Joe Puma)
14. Re: Cannot read Baofeng
BF-888S (Joe Puma)
----------------------------------------------------------------------
Message: 1
Date: Sat, 20 May 2017 15:36:37 -0400
From: Jim Unroe <rock.unroe at gmail.com>
Subject: Re: [chirp_users] Cannot read
Baofeng BF-888S
To: Discussion of CHIRP <chirp_users at intrepid.danplanet.com>
Message-ID:
<CADnO8U4_wsaCLet=nu=0a90pNzdt=DQc+i7v0b_A_xXK9CTowA at mail.gmail.com>
Content-Type: text/plain;
charset="utf-8"
On Sat, May 20, 2017 at 11:08 AM, Herb
Gerhardt <hgerhardt at wavecable.com>
wrote:
> I have been fighting similar
problems on Win10 on my Baofeng UV-5R+. I too
> rolled back the driver to 3.2.0.0
to get my "genuine" cable that I purchase
> from HRO to work once I upgraded
to Win10. It worked fine on Win7 and never
> had a problem with the latest
driver but would not work on Win10 till I
> rolled the driver back. I
then turned off the auto driver updates for this
> device. Everything worked
fine after rolling the driver back.
>
> A few months later when I tried to
read the radio again, it would not
> connect. I checked the
driver and it was still the 3.2.0.0 driver in my
> listing. It took me several
days till I updated the driver to the latest
> driver which of course did not
work, but when I rolled it back again the
> 3.2.0.0 driver from the pick list
for this device, it began to work again.
> Don't ask me what is going on but
then set it back for auto updates. I will
> now just roll the driver back
every time I want to use this cable.
>
> I suggest you try to update your
driver and then roll it back again to
> 3.2.0.0 to see if that works for
you. I know it sounds stupid but it is
> worth a try since it worked for
me.
>
>
> Herb, KB7UVC
> NW APRS Group, West Sound
Coordinator
> Our WEB Site: http://blog.nwaprs.info/
There is no need to disable updates. If
Windows does update your
Prolific driver, the previous driver is
still installed. All you have
to do is go into Device Manager and
re-select the driver version that
you want to use. I keep several
Prolific driver versions installed and
switch between then at will for testing
purposes.
Jim KC9HI
-------------- next part
--------------
A non-text attachment was scrubbed...
Name: ProlificDrivers2.jpg
Type: image/jpeg
Size: 161541 bytes
Desc: not available
Url :
http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20170520/40ab39a9/attachment-0001.jpg
------------------------------
Message: 2
Date: Sat, 20 May 2017 17:58:49 -0400
From: Rich Baker <rbakedq at gmail.com>
Subject: Re: [chirp_users] Leixen
VV-898E on MacOS? (was:
...daily-20170501
repeatable crash)
To: Discussion of CHIRP <chirp_users at intrepid.danplanet.com>
Message-ID:
<CAELWbPHggmTKrpxz-nTzfz-m2RxrEts0WSatBGaV3zZMA6V1ng at mail.gmail.com>
Content-Type: text/plain;
charset="utf-8"
Unsubscribe me from this list NOW.
On Sat, May 20, 2017 at 1:59 PM, Steve
Sergeant <stevesgt at effable.com>
wrote:
> Just to ping the group again:
>
> Has anybody out there had recent
luck programming the Leixen VV-898E
> using a recent build of Chirp on
MacOS?
>
>
>
> On 5/2/17 0:08 AM, Steve Sergeant
wrote:
> > I just installed
chirp-daily-20170501.app to try. I am attempting to
> > copy setups from one Leixen
VV-898E radio into several others.
> >
> > However, a fraction of a
second after the screen fills with the data
> > from the radio, Chirp
unexpectedly quits, and I'm given the opportunity
> > to send a report to Apple.
> >
> > My system is:
> >
> > Macbook Air 11"
(MacBookAir6,1)
> > MacOS X 10.11.6 (15G1421)
> > 4GB RAM
> >
> > The last line in
.chirp/debug.log reads:
> >
/Users/username/Applications/chirp-daily-20170501.app/
>
Contents/MacOS/../Resources/chirp/chirpw:143:
> > PangoWarning: Invalid UTF-8
string passed to pango_layout_set_text()
> > gtk.main()
> >
> > I'm using the
osx-pl2303-installer.pkg for my serial driver. This is
> > currently the only radio for
which I have a programming cable.
>
_______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to Rich at
rbakedq at gmail.com
> To unsubscribe, send an email to
chirp_users-unsubscribe@
> intrepid.danplanet.com
>
--
S. Richard Baker
250 Furnace Dock Road
Cortlandt Manor, NY 10567
Home: 914-736-1350
Cell: 917-922-2463
Email: rbakedq at gmail.com
-------------- next part
--------------
An HTML attachment was scrubbed...
URL:
http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20170520/00d7f0f7/attachment-0001.html
------------------------------
Message: 3
Date: Sat, 20 May 2017 17:59:05 -0400
From: Rich Baker <rbakedq at gmail.com>
Subject: Re: [chirp_users] Cannot read
Baofeng BF-888S
To: Discussion of CHIRP <chirp_users at intrepid.danplanet.com>
Message-ID:
<CAELWbPEYTesu5jWmSHgqmF70N6MrjqCZfYx0GmpYybU4fz4iQQ at mail.gmail.com>
Content-Type: text/plain;
charset="utf-8"
Unsubscribe me from this list NOW.
On Sat, May 20, 2017 at 3:36 PM, Jim
Unroe <rock.unroe at gmail.com>
wrote:
> On Sat, May 20, 2017 at 11:08 AM,
Herb Gerhardt <hgerhardt at wavecable.com>
> wrote:
> > I have been fighting similar
problems on Win10 on my Baofeng UV-5R+. I
> too
> > rolled back the driver to
3.2.0.0 to get my "genuine" cable that I
> purchase
> > from HRO to work once I
upgraded to Win10. It worked fine on Win7 and
> never
> > had a problem with the latest
driver but would not work on Win10 till I
> > rolled the driver back.
I then turned off the auto driver updates for
> this
> > device. Everything
worked fine after rolling the driver back.
> >
> > A few months later when I
tried to read the radio again, it would not
> > connect. I checked the
driver and it was still the 3.2.0.0 driver in my
> > listing. It took me
several days till I updated the driver to the latest
> > driver which of course did
not work, but when I rolled it back again the
> > 3.2.0.0 driver from the pick
list for this device, it began to work
> again.
> > Don't ask me what is going on
but then set it back for auto updates. I
> will
> > now just roll the driver back
every time I want to use this cable.
> >
> > I suggest you try to update
your driver and then roll it back again to
> > 3.2.0.0 to see if that works
for you. I know it sounds stupid but it is
> > worth a try since it worked
for me.
> >
> >
> > Herb, KB7UVC
> > NW APRS Group, West Sound
Coordinator
> > Our WEB Site: http://blog.nwaprs.info/
>
> There is no need to disable
updates. If Windows does update your
> Prolific driver, the previous
driver is still installed. All you have
> to do is go into Device Manager
and re-select the driver version that
> you want to use. I keep several
Prolific driver versions installed and
> switch between then at will for
testing purposes.
>
> Jim KC9HI
>
>
_______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to Rich at
rbakedq at gmail.com
> To unsubscribe, send an email to
chirp_users-unsubscribe@
> intrepid.danplanet.com
>
--
S. Richard Baker
250 Furnace Dock Road
Cortlandt Manor, NY 10567
Home: 914-736-1350
Cell: 917-922-2463
Email: rbakedq at gmail.com
-------------- next part
--------------
An HTML attachment was scrubbed...
URL:
http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20170520/3ef22303/attachment-0001.html
------------------------------
Message: 4
Date: Sat, 20 May 2017 15:06:24 -0700
From: Jardy Dawson <jardy72 at yahoo.com>
Subject: Re: [chirp_users] Leixen
VV-898E on MacOS? (was:
...daily-20170501 repeatable crash)
To: Discussion of CHIRP <chirp_users at intrepid.danplanet.com>
Message-ID: <E64697DE-5BA1-4595-AC56-99B0663E9B06 at yahoo.com>
Content-Type: text/plain;
charset="us-ascii"
You have to do that yourself by READING
THE LINKS AT THE BOTTOM OF EACH EMAIL.
Jardy Dawson
WA7JRD Ham Radio
Message relayed from secret Hillary
Clinton server, located in the basement of her house.
OOPS, you aren't supposed to know that!
On May 20, 2017, at 14:58, Rich Baker
<rbakedq at gmail.com>
wrote:
Unsubscribe me from this list
NOW.
> On Sat, May 20, 2017 at 1:59 PM,
Steve Sergeant <stevesgt at effable.com>
wrote:
> Just to ping the group again:
>
> Has anybody out there had recent
luck programming the Leixen VV-898E
> using a recent build of Chirp on
MacOS?
>
>
>
> On 5/2/17 0:08 AM, Steve Sergeant
wrote:
> > I just installed
chirp-daily-20170501.app to try. I am attempting to
> > copy setups from one Leixen
VV-898E radio into several others.
> >
> > However, a fraction of a
second after the screen fills with the data
> > from the radio, Chirp
unexpectedly quits, and I'm given the opportunity
> > to send a report to Apple.
> >
> > My system is:
> >
> > Macbook Air 11"
(MacBookAir6,1)
> > MacOS X 10.11.6 (15G1421)
> > 4GB RAM
> >
> > The last line in
.chirp/debug.log reads:
> >
/Users/username/Applications/chirp-daily-20170501.app/Contents/MacOS/../Resources/chirp/chirpw:143: > > PangoWarning: Invalid UTF-8 string passed to pango_layout_set_text() > > gtk.main() > > > > I'm using the osx-pl2303-installer.pkg for my serial driver. This is > > currently the only radio for which I have a programming cable. > _______________________________________________ > chirp_users mailing list > chirp_users at intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > This message was sent to Rich at rbakedq at gmail.com > To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com -- S. Richard Baker 250 Furnace Dock Road Cortlandt Manor, NY 10567 Home: 914-736-1350 Cell: 917-922-2463 Email: rbakedq at gmail.com _______________________________________________ chirp_users mailing list chirp_users at intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Jardy at jardy72 at yahoo.com To unsubscribe, send an email tochirp_users-unsubscribe at intrepid.danplanet.com -------------- next part -------------- An HTML attachment was scrubbed... URL:http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20170520/7bfa552d/attachment-0001.html ------------------------------ Message: 5 Date: Sat, 20 May 2017 15:07:04 -0700 From: Jardy Dawson <jardy72 at yahoo.com> Subject: Re: [chirp_users] Cannot read Baofeng BF-888S To: Discussion of CHIRP <chirp_users at intrepid.danplanet.com> Message-ID: <DA466B25-CD12-4633-B731-5B3B12630FC0 at yahoo.com> Content-Type: text/plain; charset="us-ascii" Unsub yourself. Jardy Dawson WA7JRD Ham Radio Message relayed from secret Hillary Clinton server, located in the basement of her house. OOPS, you aren't supposed to know that! On May 20, 2017, at 14:59, Rich Baker <rbakedq at gmail.com> wrote: Unsubscribe me from this list NOW. > On Sat, May 20, 2017 at 3:36 PM, Jim Unroe <rock.unroe at gmail.com> wrote: > On Sat, May 20, 2017 at 11:08 AM, Herb Gerhardt <hgerhardt at wavecable.com> wrote: > > I have been fighting similar problems on Win10 on my Baofeng UV-5R+. I too > > rolled back the driver to 3.2.0.0 to get my "genuine" cable that I purchase > > from HRO to work once I upgraded to Win10. It worked fine on Win7 and never > > had a problem with the latest driver but would not work on Win10 till I > > rolled the driver back. I then turned off the auto driver updates for this > > device. Everything worked fine after rolling the driver back. > > > > A few months later when I tried to read the radio again, it would not > > connect. I checked the driver and it was still the 3.2.0.0 driver in my > > listing. It took me several days till I updated the driver to the latest > > driver which of course did not work, but when I rolled it back again the > > 3.2.0.0 driver from the pick list for this device, it began to work again. > > Don't ask me what is going on but then set it back for auto updates. I will > > now just roll the driver back every time I want to use this cable. > > > > I suggest you try to update your driver and then roll it back again to > > 3.2.0.0 to see if that works for you. I know it sounds stupid but it is > > worth a try since it worked for me. > > > > > > Herb, KB7UVC > > NW APRS Group, West Sound Coordinator > > Our WEB Site: http://blog.nwaprs.info/ > > There is no need to disable updates. If Windows does update your > Prolific driver, the previous driver is still installed. All you have > to do is go into Device Manager and re-select the driver version that > you want to use. I keep several Prolific driver versions installed and > switch between then at will for testing purposes. > > Jim KC9HI > > _______________________________________________ > chirp_users mailing list > chirp_users at intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > This message was sent to Rich at rbakedq at gmail.com > To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com -- S. Richard Baker 250 Furnace Dock Road Cortlandt Manor, NY 10567 Home: 914-736-1350 Cell: 917-922-2463 Email: rbakedq at gmail.com _______________________________________________ chirp_users mailing list chirp_users at intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Jardy at jardy72 at yahoo.com To unsubscribe, send an email tochirp_users-unsubscribe at intrepid.danplanet.com -------------- next part -------------- An HTML attachment was scrubbed... URL:http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20170520/ef1b4428/attachment-0001.html ------------------------------ Message: 6 Date: Sat, 20 May 2017 15:06:24 -0700 From: Jim McCorison <jimmcc at mccorison.com> Subject: Re: [chirp_users] Cannot read Baofeng BF-888S To: Discussion of CHIRP <chirp_users at intrepid.danplanet.com> Message-ID: <3E9DA26F-DC85-4AA2-9A7E-AF109E11437C at mccorison.com> Content-Type: text/plain; charset="us-ascii" Wow! What a polite request. I just can't try and help you fast enough. Not. Jim McCorison Orcas Island, WA > On May 20, 2017, at 2:59 PM, Rich Baker <rbakedq at gmail.com> wrote: > > Unsubscribe me from this list NOW. > >> On Sat, May 20, 2017 at 3:36 PM, Jim Unroe <rock.unroe at gmail.com> wrote: >> On Sat, May 20, 2017 at 11:08 AM, Herb Gerhardt <hgerhardt at wavecable.com> wrote: >> > I have been fighting similar problems on Win10 on my Baofeng UV-5R+. I too >> > rolled back the driver to 3.2.0.0 to get my "genuine" cable that I purchase >> > from HRO to work once I upgraded to Win10. It worked fine on Win7 and never >> > had a problem with the latest driver but would not work on Win10 till I >> > rolled the driver back. I then turned off the auto driver updates for this >> > device. Everything worked fine after rolling the driver back. >> > >> > A few months later when I tried to read the radio again, it would not >> > connect. I checked the driver and it was still the 3.2.0.0 driver in my >> > listing. It took me several days till I updated the driver to the latest >> > driver which of course did not work, but when I rolled it back again the >> > 3.2.0.0 driver from the pick list for this device, it began to work again. >> > Don't ask me what is going on but then set it back for auto updates. I will >> > now just roll the driver back every time I want to use this cable. >> > >> > I suggest you try to update your driver and then roll it back again to >> > 3.2.0.0 to see if that works for you. I know it sounds stupid but it is >> > worth a try since it worked for me. >> > >> > >> > Herb, KB7UVC >> > NW APRS Group, West Sound Coordinator >> > Our WEB Site: http://blog.nwaprs.info/ >> >> There is no need to disable updates. If Windows does update your >> Prolific driver, the previous driver is still installed. All you have >> to do is go into Device Manager and re-select the driver version that >> you want to use. I keep several Prolific driver versions installed and >> switch between then at will for testing purposes. >> >> Jim KC9HI >> >> _______________________________________________ >> chirp_users mailing list >> chirp_users at intrepid.danplanet.com >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >> This message was sent to Rich at rbakedq at gmail.com >> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com > > > > -- > S. Richard Baker > 250 Furnace Dock Road > Cortlandt Manor, NY 10567 > > Home: 914-736-1350 > Cell: 917-922-2463 > Email: rbakedq at gmail.com > _______________________________________________ > chirp_users mailing list > chirp_users at intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > This message was sent to K2SON at jimmcc at mccorison.com > To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com -------------- next part -------------- An HTML attachment was scrubbed... URL:http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20170520/4f76cc98/attachment-0001.html ------------------------------ Message: 7 Date: Sat, 20 May 2017 19:29:42 -0400 From: Rich Baker <rbakedq at gmail.com> Subject: Re: [chirp_users] Leixen VV-898E on MacOS? (was: ...daily-20170501 repeatable crash) To: Jardy Dawson <jardy72 at yahoo.com>, Discussion of CHIRP <chirp_users at intrepid.danplanet.com> Message-ID: <CAELWbPGOpWuJE5WYt0n8CN9u8q9+PzH5swHspN+D6J=zBNbSFg at mail.gmail.com> Content-Type: text/plain; charset="utf-8" I have done that over 10 times now. It does not work. On Sat, May 20, 2017 at 6:06 PM, Jardy Dawson via chirp_users < chirp_users at intrepid.danplanet.com> wrote: > You have to do that yourself by READING THE LINKS AT THE BOTTOM OF EACH > EMAIL. > > Jardy Dawson > WA7JRD Ham Radio > > Message relayed from secret Hillary Clinton server, located in the > basement of her house. OOPS, you aren't supposed to know that! > > On May 20, 2017, at 14:58, Rich Baker <rbakedq at gmail.com> wrote: > > Unsubscribe me from this list NOW. > > On Sat, May 20, 2017 at 1:59 PM, Steve Sergeant <stevesgt at effable.com> > wrote: > >> Just to ping the group again: >> >> Has anybody out there had recent luck programming the Leixen VV-898E >> using a recent build of Chirp on MacOS? >> >> >> >> On 5/2/17 0:08 AM, Steve Sergeant wrote: >> > I just installed chirp-daily-20170501.app to try. I am attempting to >> > copy setups from one Leixen VV-898E radio into several others. >> > >> > However, a fraction of a second after the screen fills with the data >> > from the radio, Chirp unexpectedly quits, and I'm given the opportunity >> > to send a report to Apple. >> > >> > My system is: >> > >> > Macbook Air 11" (MacBookAir6,1) >> > MacOS X 10.11.6 (15G1421) >> > 4GB RAM >> > >> > The last line in .chirp/debug.log reads: >> > /Users/username/Applications/chirp-daily-20170501.app/Conten >> ts/MacOS/../Resources/chirp/chirpw:143: >> > PangoWarning: Invalid UTF-8 string passed to pango_layout_set_text() >> > gtk.main() >> > >> > I'm using the osx-pl2303-installer.pkg for my serial driver. This is >> > currently the only radio for which I have a programming cable. >> _______________________________________________ >> chirp_users mailing list >> chirp_users at intrepid.danplanet.com >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >> This message was sent to Rich at rbakedq at gmail.com >> To unsubscribe, send an email to chirp_users-unsubscribe at intrep >> id.danplanet.com >> > > > > -- > S. Richard Baker > 250 Furnace Dock Road > Cortlandt Manor, NY 10567 > > Home: 914-736-1350 <(914)%20736-1350> > Cell: 917-922-2463 <(917)%20922-2463> > Email: rbakedq at gmail.com > _______________________________________________ > chirp_users mailing list > chirp_users at intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > This message was sent to Jardy at jardy72 at yahoo.com > To unsubscribe, send an email to chirp_users-unsubscribe@ > intrepid.danplanet.com > > _______________________________________________ > chirp_users mailing list > chirp_users at intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > This message was sent to Rich at rbakedq at gmail.com > To unsubscribe, send an email to chirp_users-unsubscribe@ > intrepid.danplanet.com > -- S. Richard Baker 250 Furnace Dock Road Cortlandt Manor, NY 10567 Home: 914-736-1350 Cell: 917-922-2463 Email: rbakedq at gmail.com -------------- next part -------------- An HTML attachment was scrubbed... URL:http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20170520/b15c20c7/attachment-0001.html ------------------------------ Message: 8 Date: Sat, 20 May 2017 19:30:55 -0400 From: Rich Baker <rbakedq at gmail.com> Subject: Re: [chirp_users] Cannot read Baofeng BF-888S To: Discussion of CHIRP <chirp_users at intrepid.danplanet.com> Message-ID: <CAELWbPGYBw51s9AL8BoZuUighp_aUj05Dfj_vL9ZWKyqidhp=Q at mail.gmail.com> Content-Type: text/plain; charset="utf-8" Tried to unsubscribe over 10 times both on the website and by sending emails. On Sat, May 20, 2017 at 6:06 PM, Jim McCorison <jimmcc at mccorison.com> wrote: > Wow! What a polite request. I just can't try and help you fast enough. > > Not. > > Jim McCorison > Orcas Island, WA > > On May 20, 2017, at 2:59 PM, Rich Baker <rbakedq at gmail.com> wrote: > > Unsubscribe me from this list NOW. > > On Sat, May 20, 2017 at 3:36 PM, Jim Unroe <rock.unroe at gmail.com> wrote: > >> On Sat, May 20, 2017 at 11:08 AM, Herb Gerhardt <hgerhardt at wavecable.com> >> wrote: >> > I have been fighting similar problems on Win10 on my Baofeng UV-5R+. I >> too >> > rolled back the driver to 3.2.0.0 to get my "genuine" cable that I >> purchase >> > from HRO to work once I upgraded to Win10. It worked fine on Win7 and >> never >> > had a problem with the latest driver but would not work on Win10 till I >> > rolled the driver back. I then turned off the auto driver updates for >> this >> > device. Everything worked fine after rolling the driver back. >> > >> > A few months later when I tried to read the radio again, it would not >> > connect. I checked the driver and it was still the 3.2.0.0 driver in my >> > listing. It took me several days till I updated the driver to the >> latest >> > driver which of course did not work, but when I rolled it back again the >> > 3.2.0.0 driver from the pick list for this device, it began to work >> again. >> > Don't ask me what is going on but then set it back for auto updates. I >> will >> > now just roll the driver back every time I want to use this cable. >> > >> > I suggest you try to update your driver and then roll it back again to >> > 3.2.0.0 to see if that works for you. I know it sounds stupid but it is >> > worth a try since it worked for me. >> > >> > >> > Herb, KB7UVC >> > NW APRS Group, West Sound Coordinator >> > Our WEB Site: http://blog.nwaprs.info/ >> >> There is no need to disable updates. If Windows does update your >> Prolific driver, the previous driver is still installed. All you have >> to do is go into Device Manager and re-select the driver version that >> you want to use. I keep several Prolific driver versions installed and >> switch between then at will for testing purposes. >> >> Jim KC9HI >> >> _______________________________________________ >> chirp_users mailing list >> chirp_users at intrepid.danplanet.com >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >> This message was sent to Rich at rbakedq at gmail.com >> To unsubscribe, send an email to chirp_users-unsubscribe at intrep >> id.danplanet.com >> > > > > -- > S. Richard Baker > 250 Furnace Dock Road > Cortlandt Manor, NY 10567 > > Home: 914-736-1350 <(914)%20736-1350> > Cell: 917-922-2463 <(917)%20922-2463> > Email: rbakedq at gmail.com > > _______________________________________________ > chirp_users mailing list > chirp_users at intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > This message was sent to K2SON at jimmcc at mccorison.com > To unsubscribe, send an email to chirp_users-unsubscribe@ > intrepid.danplanet.com > > > _______________________________________________ > chirp_users mailing list > chirp_users at intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > This message was sent to Rich at rbakedq at gmail.com > To unsubscribe, send an email to chirp_users-unsubscribe@ > intrepid.danplanet.com > -- S. Richard Baker 250 Furnace Dock Road Cortlandt Manor, NY 10567 Home: 914-736-1350 Cell: 917-922-2463 Email: rbakedq at gmail.com -------------- next part -------------- An HTML attachment was scrubbed... URL:http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20170520/70cc1511/attachment-0001.html ------------------------------ Message: 9 Date: Sat, 20 May 2017 18:03:34 -0700 From: Jim McCorison <jimmcc at mccorison.com> Subject: Re: [chirp_users] Cannot read Baofeng BF-888S To: Discussion of CHIRP <chirp_users at intrepid.danplanet.com> Message-ID: <20885233-494D-4BE4-B06E-CDBE22B4C2BF at mccorison.com> Content-Type: text/plain; charset="utf-8" Perhaps it you reached out with a polite request along the lines of ?I?m having problems unsubscribing from this list. I?ve sent an unsubscribe request email without success and I?ve tried the website without success. Does any body have any ideas what I?m doing wrong?? Bonus points for sending it as a separate thread with s subject of something like ?Need help. Problems unsubscribing." Such an inquiry will probably get you a lot more assistance than just throwing a grenade into the mailing list. --- Jim McCorison Orcas Island, WA > On May 20, 2017, at 4:30 PM, Rich Baker <rbakedq at gmail.com> wrote: > > Tried to unsubscribe over 10 times both on the website and by sending emails. > > On Sat, May 20, 2017 at 6:06 PM, Jim McCorison <jimmcc at mccorison.com <mailto:jimmcc at mccorison.com>> wrote: > Wow! What a polite request. I just can't try and help you fast enough. > > Not. > > Jim McCorison > Orcas Island, WA > > On May 20, 2017, at 2:59 PM, Rich Baker <rbakedq at gmail.com <mailto:rbakedq at gmail.com>> wrote: > >> Unsubscribe me from this list NOW. >> >> On Sat, May 20, 2017 at 3:36 PM, Jim Unroe <rock.unroe at gmail.com <mailto:rock.unroe at gmail.com>> wrote: >> On Sat, May 20, 2017 at 11:08 AM, Herb Gerhardt <hgerhardt at wavecable.com <mailto:hgerhardt at wavecable.com>> wrote: >> > I have been fighting similar problems on Win10 on my Baofeng UV-5R+. I too >> > rolled back the driver to 3.2.0.0 to get my "genuine" cable that I purchase >> > from HRO to work once I upgraded to Win10. It worked fine on Win7 and never >> > had a problem with the latest driver but would not work on Win10 till I >> > rolled the driver back. I then turned off the auto driver updates for this >> > device. Everything worked fine after rolling the driver back. >> > >> > A few months later when I tried to read the radio again, it would not >> > connect. I checked the driver and it was still the 3.2.0.0 driver in my >> > listing. It took me several days till I updated the driver to the latest >> > driver which of course did not work, but when I rolled it back again the >> > 3.2.0.0 driver from the pick list for this device, it began to work again. >> > Don't ask me what is going on but then set it back for auto updates. I will >> > now just roll the driver back every time I want to use this cable. >> > >> > I suggest you try to update your driver and then roll it back again to >> > 3.2.0.0 to see if that works for you. I know it sounds stupid but it is >> > worth a try since it worked for me. >> > >> > >> > Herb, KB7UVC >> > NW APRS Group, West Sound Coordinator >> > Our WEB Site: http://blog.nwaprs.info/ <http://blog.nwaprs.info/> >> >> There is no need to disable updates. If Windows does update your >> Prolific driver, the previous driver is still installed. All you have >> to do is go into Device Manager and re-select the driver version that >> you want to use. I keep several Prolific driver versions installed and >> switch between then at will for testing purposes. >> >> Jim KC9HI >> >> _______________________________________________ >> chirp_users mailing list >> chirp_users at intrepid.danplanet.com <mailto:chirp_users at intrepid.danplanet.com> >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users <http://intrepid.danplanet.com/mailman/listinfo/chirp_users> >> This message was sent to Rich at rbakedq at gmail.com <mailto:rbakedq at gmail.com> >> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com <mailto:chirp_users-unsubscribe at intrepid.danplanet.com> >> >> >> >> -- >> S. Richard Baker >> 250 Furnace Dock Road >> Cortlandt Manor, NY 10567 >> >> Home: 914-736-1350 <tel:(914)%20736-1350> >> Cell: 917-922-2463 <tel:(917)%20922-2463> >> Email: rbakedq at gmail.com <mailto:rbakedq at gmail.com>_______________________________________________ >> chirp_users mailing list >> chirp_users at intrepid.danplanet.com <mailto:chirp_users at intrepid.danplanet.com> >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users <http://intrepid.danplanet.com/mailman/listinfo/chirp_users> >> This message was sent to K2SON at jimmcc at mccorison.com <mailto:jimmcc at mccorison.com> >> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com <mailto:chirp_users-unsubscribe at intrepid.danplanet.com> > _______________________________________________ > chirp_users mailing list > chirp_users at intrepid.danplanet.com <mailto:chirp_users at intrepid.danplanet.com> > http://intrepid.danplanet.com/mailman/listinfo/chirp_users <http://intrepid.danplanet.com/mailman/listinfo/chirp_users> > This message was sent to Rich at rbakedq at gmail.com <mailto:rbakedq at gmail.com> > To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com <mailto:chirp_users-unsubscribe at intrepid.danplanet.com> > > > > -- > S. Richard Baker > 250 Furnace Dock Road > Cortlandt Manor, NY 10567 > > Home: 914-736-1350 > Cell: 917-922-2463 > Email: rbakedq at gmail.com <mailto:rbakedq at gmail.com>_______________________________________________ > chirp_users mailing list > chirp_users at intrepid.danplanet.com <mailto:chirp_users at intrepid.danplanet.com> > http://intrepid.danplanet.com/mailman/listinfo/chirp_users <http://intrepid.danplanet.com/mailman/listinfo/chirp_users> > This message was sent to K2SON at jimmcc at mccorison.com <mailto:jimmcc at mccorison.com> > To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com <mailto:chirp_users-unsubscribe at intrepid.danplanet.com> -------------- next part -------------- An HTML attachment was scrubbed... URL:http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20170520/049c5d1b/attachment-0001.html ------------------------------ Message: 10 Date: Sat, 20 May 2017 19:40:49 -0600 From: NNN Wx <nthreewx at gmail.com> Subject: [chirp_users] FT2D To: chirp_users at intrepid.danplanet.com Message-ID: <EB99DD23-C6B9-482B-AC28-220025DC2B3B at gmail.com> Content-Type: text/plain; charset=utf-8 I see ?bug? numbers 3325 and 3257 from last year, hoping support for Yaesu FT2D radio will work. It?s in the wish list, and doesn?t seem to need hardware for testing. I?m interested in getting chirp to work, and for some insights into how to get the serial connection to work on Macintosh OS X 10.12.5. HOW CAN I HELP (assuming this just needs effort)?? ------------------------------ Message: 11 Date: Sun, 21 May 2017 02:25:30 +0000 (UTC) From: Bob Decker <k7bd at yahoo.com> Subject: Re: [chirp_users] chirp_users Digest, Vol 101, Issue 19 To: "chirp_users at intrepid.danplanet.com" <chirp_users at intrepid.danplanet.com> Message-ID: <1930811399.2660365.1495333530472 at mail.yahoo.com> Content-Type: text/plain; charset="utf-8" Your method of removal from list did not work. I must cut back mailwh9ch I do not use.? Remove my address. The only other way to remove youre-mail by listing it as spam.ThanksBob On Saturday, May 20, 2017 12:00 PM, "chirp_users-request at intrepid.danplanet.com" <chirp_users-request at intrepid.danplanet.com> wrote: Send chirp_users mailing list submissions to ??? chirp_users at intrepid.danplanet.com To subscribe or unsubscribe via the World Wide Web, visit ??? http://intrepid.danplanet.com/mailman/listinfo/chirp_users or, via email, send a message with subject or body 'help' to ??? chirp_users-request at intrepid.danplanet.com You can reach the person managing the list at ??? chirp_users-owner at intrepid.danplanet.com When replying, please edit your Subject line so it is more specific than "Re: Contents of chirp_users digest..." Today's Topics: ? 1. RepeaterBook Proximety Not Accurate? (John Kobeck) ? 2. Re: RepeaterBook Proximety Not Accurate? (Jim Unroe) ? 3. Re: Cannot read Baofeng BF-888S (Herb Gerhardt) ? 4. Re: Cannot read Baofeng BF-888S (Amnon Zohar) ? 5. Re: Cannot read Baofeng BF-888S (Glenn At Home) ? 6. Leixen VV-898E on MacOS? (was: ...daily-20170501??? repeatable ? ? ? crash) (Steve Sergeant) ---------------------------------------------------------------------- Message: 1 Date: Fri, 19 May 2017 23:04:47 -0400 From: John Kobeck <johnkobeck at me.com> Subject: [chirp_users] RepeaterBook Proximety Not Accurate? To: chirp_users at intrepid.danplanet.com Message-ID: <5F40902E-156A-415A-B687-A0118642A496 at me.com> Content-Type: text/plain; charset=utf-8 Hello Chirpers; I have a question. I am trying to program repeaters into a Kenwood TMV7. I have been using RepeaterBooks Proximity search. When setting a Manhattan? zip code for example, it doesn?t seem to matter if I indicate a 100 mile radius or a 300 mile radius. It only seems pull about a 15 miles radius. Is there a default that won?t allow a larger range? 73s KC2MPG ------------------------------ Message: 2 Date: Sat, 20 May 2017 05:48:35 -0400 From: Jim Unroe <rock.unroe at gmail.com> Subject: Re: [chirp_users] RepeaterBook Proximety Not Accurate? To: Discussion of CHIRP <chirp_users at intrepid.danplanet.com> Message-ID: ??? <CADnO8U7LPAPZM6s2Y6mtYQd1qz+t+QNJR9xDXG_AAX2kbBvqug at mail.gmail.com> Content-Type: text/plain; charset="UTF-8" On Fri, May 19, 2017 at 11:04 PM, John Kobeck <johnkobeck at me.com> wrote: > > Hello Chirpers; > > I have a question. I am trying to program repeaters into a Kenwood TMV7. I have been using RepeaterBooks Proximity search. When setting a Manhattan? zip code for example, it doesn?t seem to matter if I indicate a 100 mile radius or a 300 mile radius. It only seems pull about a 15 miles radius. Is there a default that won?t allow a larger range? > > 73s > KC2MPG Using "Import from data source", "Location" = 10001 and "Band" = "2 meters (144MHz)", I the following numbers of repeaters are retrieved. Distance: # of repeaters 15: 50 100: 367 300: 1387 Jim KC9HI ------------------------------ Message: 3 Date: Sat, 20 May 2017 08:08:14 -0700 From: "Herb Gerhardt" <hgerhardt at wavecable.com> Subject: Re: [chirp_users] Cannot read Baofeng BF-888S To: "'Discussion of CHIRP'" <chirp_users at intrepid.danplanet.com> Message-ID: <001301d2d17a$e7936ea0$b6ba4be0$@com> Content-Type: text/plain;??? charset="us-ascii" I have been fighting similar problems on Win10 on my Baofeng UV-5R+.? I too rolled back the driver to 3.2.0.0 to get my "genuine" cable that I purchase from HRO to work once I upgraded to Win10.? It worked fine on Win7 and never had a problem with the latest driver but would not work on Win10 till I rolled the driver back.? I then turned off the auto driver updates for this device.? Everything worked fine after rolling the driver back. A few months later when I tried to read the radio again, it would not connect.? I checked the driver and it was still the 3.2.0.0 driver in my listing.? It took me several days till I updated the driver to the latest driver which of course did not work, but when I rolled it back again the 3.2.0.0 driver from the pick list for this device, it began to work again. Don't ask me what is going on but then set it back for auto updates.? I will now just roll the driver back every time I want to use this cable. I suggest you try to update your driver and then roll it back again to 3.2.0.0 to see if that works for you.? I know it sounds stupid but it is worth a try since it worked for me. Herb, KB7UVC NW APRS Group, West Sound Coordinator Our WEB Site:? http://blog.nwaprs.info/ -----Original Message----- From: chirp_users-bounces at intrepid.danplanet.com [mailto:chirp_users-bounces at intrepid.danplanet.com] On Behalf Of YT9TP - Pedja Sent: Friday, May 19, 2017 1:08 AM To: chirp_users at intrepid.danplanet.com Subject: [chirp_users] Cannot read Baofeng BF-888S I have strange issue with Windows 10, prolific serial adapter and BF-888S. It reports unable to download from radio. Driver is proper (version 3.2.0.0, update is disabled), and Chirp works fine with the same adapter and other radio (Baofeng UV-B5) reading and writing. I tried four different BF-888S and neither can be read. However, when I use the same USB adapter on my old Windows XP computer, Chirp easily reads and writes those BF-888S. Has anyone met with this problem? -- YT9TP, Pedja http://www.yt9tp.iz.rs --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus ------------------------------ Message: 4 Date: Sat, 20 May 2017 18:23:30 +0300 From: Amnon Zohar <amnon.zohar at gmail.com> Subject: Re: [chirp_users] Cannot read Baofeng BF-888S To: Discussion of CHIRP <chirp_users at intrepid.danplanet.com> Message-ID: ??? <CAN5HzcQAXwM2rBUjdtwkMCOb7_XfsmQ6PgMSqsc5M4B0i19F-A at mail.gmail.com> Content-Type: text/plain; charset="utf-8" I guess some update of win10 change some part of the driver without changing the driver version number. Redowngrading probably fix this. But this just a wild guess. The solution is important. The reason is less important ?????? 20 ???? 2017 18:09,? "Herb Gerhardt" <hgerhardt at wavecable.com> ???: > I have been fighting similar problems on Win10 on my Baofeng UV-5R+.? I too > rolled back the driver to 3.2.0.0 to get my "genuine" cable that I purchase > from HRO to work once I upgraded to Win10.? It worked fine on Win7 and > never > had a problem with the latest driver but would not work on Win10 till I > rolled the driver back.? I then turned off the auto driver updates for this > device.? Everything worked fine after rolling the driver back. > > A few months later when I tried to read the radio again, it would not > connect.? I checked the driver and it was still the 3.2.0.0 driver in my > listing.? It took me several days till I updated the driver to the latest > driver which of course did not work, but when I rolled it back again the > 3.2.0.0 driver from the pick list for this device, it began to work again. > Don't ask me what is going on but then set it back for auto updates.? I > will > now just roll the driver back every time I want to use this cable. > > I suggest you try to update your driver and then roll it back again to > 3.2.0.0 to see if that works for you.? I know it sounds stupid but it is > worth a try since it worked for me. > > > Herb, KB7UVC > NW APRS Group, West Sound Coordinator > Our WEB Site:? http://blog.nwaprs.info/ > > > > > > -----Original Message----- > From: chirp_users-bounces at intrepid.danplanet.com > [mailto:chirp_users-bounces at intrepid.danplanet.com] On Behalf Of YT9TP - > Pedja > Sent: Friday, May 19, 2017 1:08 AM > To: chirp_users at intrepid.danplanet.com > Subject: [chirp_users] Cannot read Baofeng BF-888S > > I have strange issue with Windows 10, prolific serial adapter and BF-888S. > It reports unable to download from radio. > > Driver is proper (version 3.2.0.0, update is disabled), and Chirp works > fine > with the same adapter and other radio (Baofeng UV-B5) reading and writing. > > I tried four different BF-888S and neither can be read. > > However, when I use the same USB adapter on my old Windows XP computer, > Chirp easily reads and writes those BF-888S. > > Has anyone met with this problem? > > -- > > YT9TP, Pedja > http://www.yt9tp.iz.rs > > > > --- > This email has been checked for viruses by Avast antivirus software. > https://www.avast.com/antivirus > > _______________________________________________ > chirp_users mailing list > chirp_users at intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > This message was sent to amnon at amnon.zohar at gmail.com > To unsubscribe, send an email to chirp_users-unsubscribe@ > intrepid.danplanet.com > -------------- next part -------------- An HTML attachment was scrubbed... URL:http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20170520/ec65c2c2/attachment-0001.html ------------------------------ Message: 5 Date: Sat, 20 May 2017 11:13:04 -0500 From: "Glenn At Home" <GlennErvin at cableone.net> Subject: Re: [chirp_users] Cannot read Baofeng BF-888S To: "Discussion of CHIRP" <chirp_users at intrepid.danplanet.com> Message-ID: <047601d2d183$f683cf00$0601a8c0 at NUCPPYH> Content-Type: text/plain; charset="utf-8" I wonder if you did not reboot windows soon enough to solidify the change. You would think that this would not matter, but maybe Windows needs to reboot for changes such as the driver setting. Glenn I have been fighting similar problems on Win10 on my Baofeng UV-5R+.? I too rolled back the driver to 3.2.0.0 to get my "genuine" cable that I purchase from HRO to work once I upgraded to Win10.? It worked fine on Win7 and never had a problem with the latest driver but would not work on Win10 till I rolled the driver back.? I then turned off the auto driver updates for this device.? Everything worked fine after rolling the driver back. A few months later when I tried to read the radio again, it would not connect.? I checked the driver and it was still the 3.2.0.0 driver in my listing.? It took me several days till I updated the driver to the latest driver which of course did not work, but when I rolled it back again the 3.2.0.0 driver from the pick list for this device, it began to work again. Don't ask me what is going on but then set it back for auto updates.? I will now just roll the driver back every time I want to use this cable. I suggest you try to update your driver and then roll it back again to 3.2.0.0 to see if that works for you.? I know it sounds stupid but it is worth a try since it worked for me. Herb, KB7UVC NW APRS Group, West Sound Coordinator Our WEB Site:? http://blog.nwaprs.info/ -----Original Message----- From: chirp_users-bounces at intrepid.danplanet.com [mailto:chirp_users-bounces at intrepid.danplanet.com] On Behalf Of YT9TP - Pedja Sent: Friday, May 19, 2017 1:08 AM To: chirp_users at intrepid.danplanet.com Subject: [chirp_users] Cannot read Baofeng BF-888S I have strange issue with Windows 10, prolific serial adapter and BF-888S. It reports unable to download from radio. Driver is proper (version 3.2.0.0, update is disabled), and Chirp works fine with the same adapter and other radio (Baofeng UV-B5) reading and writing. I tried four different BF-888S and neither can be read. However, when I use the same USB adapter on my old Windows XP computer, Chirp easily reads and writes those BF-888S. Has anyone met with this problem? -- YT9TP, Pedja http://www.yt9tp.iz.rs --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus _______________________________________________ chirp_users mailing list chirp_users at intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to amnon at amnon.zohar at gmail.com To unsubscribe, send an email tochirp_users-unsubscribe at intrepid.danplanet.com -------------------------------------------------------------------------------- _______________________________________________ chirp_users mailing list chirp_users at intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Glenn at glennervin at cableone.net To unsubscribe, send an email tochirp_users-unsubscribe at intrepid.danplanet.com -------------- next part -------------- An HTML attachment was scrubbed... URL:http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20170520/c0433d81/attachment-0001.html ------------------------------ Message: 6 Date: Sat, 20 May 2017 10:59:00 -0700 From: Steve Sergeant <stevesgt at effable.com> Subject: [chirp_users] Leixen VV-898E on MacOS? (was: ??? ...daily-20170501??? repeatable crash) To: chirp_users at intrepid.danplanet.com Message-ID: <7623fd03-20f3-5351-6a42-7fc3f405c22a at effable.com> Content-Type: text/plain; charset=utf-8 Just to ping the group again: Has anybody out there had recent luck programming the Leixen VV-898E using a recent build of Chirp on MacOS? On 5/2/17 0:08 AM, Steve Sergeant wrote: > I just installed chirp-daily-20170501.app to try. I am attempting to > copy setups from one Leixen VV-898E radio into several others. > > However, a fraction of a second after the screen fills with the data > from the radio, Chirp unexpectedly quits, and I'm given the opportunity > to send a report to Apple. > > My system is: > > Macbook Air 11" (MacBookAir6,1) > MacOS X 10.11.6 (15G1421) > 4GB RAM > > The last line in .chirp/debug.log reads: > /Users/username/Applications/chirp-daily-20170501.app/Contents/MacOS/../Resources/chirp/chirpw:143: > PangoWarning: Invalid UTF-8 string passed to pango_layout_set_text() >? gtk.main() > > I'm using the osx-pl2303-installer.pkg for my serial driver. This is > currently the only radio for which I have a programming cable. ------------------------------ _______________________________________________ chirp_users mailing list chirp_users at intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email tochirp_users-unsubscribe at intrepid.danplanet.com End of chirp_users Digest, Vol 101, Issue 19 ******************************************** -------------- next part -------------- An HTML attachment was scrubbed... URL:http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20170521/7b6dbd28/attachment-0001.html ------------------------------ Message: 12 Date: Sat, 20 May 2017 21:28:16 -0500 From: Carrie Jackson <mssjacksonifyournasty at gmail.com> Subject: Re: [chirp_users] chirp_users Digest, Vol 101, Issue 19 To: Bob Decker <k7bd at yahoo.com>, Discussion of CHIRP <chirp_users at intrepid.danplanet.com> Message-ID: <93a354da-a162-4ad8-a2e4-25a707fed0f1 at Spark> Content-Type: text/plain; charset="utf-8" Carrie Jackson liked your e-mail Spark by Readdle(https://itunes.apple.com/app/id997102246?mt=8&uo=4&at=10l6UJ&ct=Spark_QR_viral) Spark by Readdle(https://itunes.apple.com/app/id997102246?mt=8&uo=4&at=10l6UJ&ct=Spark_QR_viral) -------------- next part -------------- An HTML attachment was scrubbed... URL:http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20170520/1bba98f9/attachment-0001.html ------------------------------ Message: 13 Date: Sun, 21 May 2017 13:58:24 -0400 From: Joe Puma <theprogramllc at yahoo.com> Subject: Re: [chirp_users] Cannot read Baofeng BF-888S To: Discussion of CHIRP <chirp_users at intrepid.danplanet.com> Message-ID: <762A954A-D894-4632-A374-F805FE65E9A1 at yahoo.com> Content-Type: text/plain; charset="us-ascii" Rich do it yourself. Read bottom of email. Sent from my iPhone > On May 20, 2017, at 5:59 PM, Rich Baker <rbakedq at gmail.com> wrote: > > Unsubscribe me from this list NOW. > >> On Sat, May 20, 2017 at 3:36 PM, Jim Unroe <rock.unroe at gmail.com> wrote: >> On Sat, May 20, 2017 at 11:08 AM, Herb Gerhardt <hgerhardt at wavecable.com> wrote: >> > I have been fighting similar problems on Win10 on my Baofeng UV-5R+. I too >> > rolled back the driver to 3.2.0.0 to get my "genuine" cable that I purchase >> > from HRO to work once I upgraded to Win10. It worked fine on Win7 and never >> > had a problem with the latest driver but would not work on Win10 till I >> > rolled the driver back. I then turned off the auto driver updates for this >> > device. Everything worked fine after rolling the driver back. >> > >> > A few months later when I tried to read the radio again, it would not >> > connect. I checked the driver and it was still the 3.2.0.0 driver in my >> > listing. It took me several days till I updated the driver to the latest >> > driver which of course did not work, but when I rolled it back again the >> > 3.2.0.0 driver from the pick list for this device, it began to work again. >> > Don't ask me what is going on but then set it back for auto updates. I will >> > now just roll the driver back every time I want to use this cable. >> > >> > I suggest you try to update your driver and then roll it back again to >> > 3.2.0.0 to see if that works for you. I know it sounds stupid but it is >> > worth a try since it worked for me. >> > >> > >> > Herb, KB7UVC >> > NW APRS Group, West Sound Coordinator >> > Our WEB Site: http://blog.nwaprs.info/ >> >> There is no need to disable updates. If Windows does update your >> Prolific driver, the previous driver is still installed. All you have >> to do is go into Device Manager and re-select the driver version that >> you want to use. I keep several Prolific driver versions installed and >> switch between then at will for testing purposes. >> >> Jim KC9HI >> >> _______________________________________________ >> chirp_users mailing list >> chirp_users at intrepid.danplanet.com >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >> This message was sent to Rich at rbakedq at gmail.com >> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com > > > > -- > S. Richard Baker > 250 Furnace Dock Road > Cortlandt Manor, NY 10567 > > Home: 914-736-1350 > Cell: 917-922-2463 > Email: rbakedq at gmail.com > _______________________________________________ > chirp_users mailing list > chirp_users at intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > This message was sent to Joe Puma at theprogramllc at yahoo.com > To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com -------------- next part -------------- An HTML attachment was scrubbed... URL:http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20170521/ec3050d6/attachment-0001.html ------------------------------ Message: 14 Date: Sun, 21 May 2017 13:59:32 -0400 From: Joe Puma <theprogramllc at yahoo.com> Subject: Re: [chirp_users] Cannot read Baofeng BF-888S To: Discussion of CHIRP <chirp_users at intrepid.danplanet.com> Message-ID: <9FDE6A55-5F80-439E-AFFE-51E5AF484F0D at yahoo.com> Content-Type: text/plain; charset="us-ascii" Lol Sent from my iPhone > On May 20, 2017, at 6:06 PM, Jim McCorison <jimmcc at mccorison.com> wrote: > > Wow! What a polite request. I just can't try and help you fast enough. > > Not. > > Jim McCorison > Orcas Island, WA > >> On May 20, 2017, at 2:59 PM, Rich Baker <rbakedq at gmail.com> wrote: >> >> Unsubscribe me from this list NOW. >> >>> On Sat, May 20, 2017 at 3:36 PM, Jim Unroe <rock.unroe at gmail.com> wrote: >>> On Sat, May 20, 2017 at 11:08 AM, Herb Gerhardt <hgerhardt at wavecable.com> wrote: >>> > I have been fighting similar problems on Win10 on my Baofeng UV-5R+. I too >>> > rolled back the driver to 3.2.0.0 to get my "genuine" cable that I purchase >>> > from HRO to work once I upgraded to Win10. It worked fine on Win7 and never >>> > had a problem with the latest driver but would not work on Win10 till I >>> > rolled the driver back. I then turned off the auto driver updates for this >>> > device. Everything worked fine after rolling the driver back. >>> > >>> > A few months later when I tried to read the radio again, it would not >>> > connect. I checked the driver and it was still the 3.2.0.0 driver in my >>> > listing. It took me several days till I updated the driver to the latest >>> > driver which of course did not work, but when I rolled it back again the >>> > 3.2.0.0 driver from the pick list for this device, it began to work again. >>> > Don't ask me what is going on but then set it back for auto updates. I will >>> > now just roll the driver back every time I want to use this cable. >>> > >>> > I suggest you try to update your driver and then roll it back again to >>> > 3.2.0.0 to see if that works for you. I know it sounds stupid but it is >>> > worth a try since it worked for me. >>> > >>> > >>> > Herb, KB7UVC >>> > NW APRS Group, West Sound Coordinator >>> > Our WEB Site: http://blog.nwaprs.info/ >>> >>> There is no need to disable updates. If Windows does update your >>> Prolific driver, the previous driver is still installed. All you have >>> to do is go into Device Manager and re-select the driver version that >>> you want to use. I keep several Prolific driver versions installed and >>> switch between then at will for testing purposes. >>> >>> Jim KC9HI >>> >>> _______________________________________________ >>> chirp_users mailing list >>> chirp_users at intrepid.danplanet.com >>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >>> This message was sent to Rich at rbakedq at gmail.com >>> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com >> >> >> >> -- >> S. Richard Baker >> 250 Furnace Dock Road >> Cortlandt Manor, NY 10567 >> >> Home: 914-736-1350 >> Cell: 917-922-2463 >> Email: rbakedq at gmail.com >> _______________________________________________ >> chirp_users mailing list >> chirp_users at intrepid.danplanet.com >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >> This message was sent to K2SON at jimmcc at mccorison.com >> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com > _______________________________________________ > chirp_users mailing list > chirp_users at intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > This message was sent to Joe Puma at theprogramllc at yahoo.com > To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com -------------- next part -------------- An HTML attachment was scrubbed... URL:http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20170521/161a0e09/attachment-0001.html ------------------------------ _______________________________________________ chirp_users mailing list chirp_users at intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email tochirp_users-unsubscribe at intrepid.danplanet.com End of chirp_users Digest, Vol 101, Issue 20 ********************************************_______________________________________________chirp_users mailing listchirp_users at intrepid.danplanet.comhttp://intrepid.danplanet.com/mailman/listinfo/chirp_usersThis message was sent to Glenn at glennervin at cableone.netTo unsubscribe, send an email tochirp_users-unsubscribe at intrepid.danplanet.com
More information about the chirp_users
mailing list