[chirp_users] kenwood/baofeng programming

[Nigel A. Gunn G8IFF/W8IFF]

Correct.

> On 03 April 2017 at 18:51 Jim McIver <jmciver at lmtribune.com> wrote:
> 
> 
> One last question....I hope. Where the kenwood QT/DQT Dec & QT/DQT Enc 
> are set to None in both columns, I just set the Chirp Tone Mode to 
> (None), correct?
> 
> thx again,
> -jm
> 
> On 4/3/2017 3:32 PM, Jim Unroe wrote:
> > Jim,
> >
> > That looks better.
> >
> > Are you doing the math to come up with the offset and shift direction?
> > If yes, here is a tip that might speed things up for you.
> >
> > Since you are getting the TX frequency directly from the Kenwood
> > software, you can enter that frequency directly into CHIRP. Just set
> > Duplex = "split" and enter the TX frequency into the Offset column.
> > The you can click the [Refresh] button and CHIRP will to the math and
> > set the Duplex and Offset values for you.
> >
> > Also you can set common setting for multiple memories at the same
> > time. For example if you forgot so switch several memories to NFM, you
> > can click, shift-click, ctrl-click as needed to highlight a few memory
> > rows. Then click the [Properties] button. Then tick the box to the
> > left of Mode and then set it to NFM and click OK. All highlighted
> > memories will be switched at the same time.
> >
> > Jim
> >
> > On Mon, Apr 3, 2017 at 6:14 PM, Jim McIver <jmciver at lmtribune.com> wrote:
> >> Thanks all. Does the attached look better?
> >> -jm
> >>
> >> On 4/3/2017 3:04 PM, Jim Unroe wrote:
> >>>
> >>> On Mon, Apr 3, 2017 at 5:44 PM, Jim McIver <jmciver at lmtribune.com> wrote:
> >>>>
> >>>> Trying to attach a jpg that shows the kenwood tk-2170 on top and baofeng
> >>>> 82c
> >>>> on the bottom.
> >>>>
> >>>> Does it look like I'm programming the baofeng correctly to match the
> >>>> kenwood?
> >>>>
> >>>> thx,
> >>>> -jm
> >>>
> >>>
> >>> Jim,
> >>>
> >>> Not the same. The Kenwood has a TX CTCSS tone programmed but not an RX
> >>> CTCSS tone. You are programming both a TX and RX CTCSS tone on the
> >>> UV-82C.
> >>>
> >>> To be the same you must change Tone Mode to Tone and put the CTCSS
> >>> tone in the Tone column.
> >>>
> >>> Jim
> >>> _______________________________________________
> >>> chirp_users mailing list
> >>> chirp_users at intrepid.danplanet.com
> >>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> >>> This message was sent to Jim M at jmciver at lmtribune.com
> >>> To unsubscribe, send an email to
> >>> chirp_users-unsubscribe at intrepid.danplanet.com
> >>>
> >>
> >>
> >> _______________________________________________
> >> chirp_users mailing list
> >> chirp_users at intrepid.danplanet.com
> >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> >> This message was sent to Jim at rock.unroe at gmail.com
> >> To unsubscribe, send an email to
> >> chirp_users-unsubscribe at intrepid.danplanet.com
> > _______________________________________________
> > chirp_users mailing list
> > chirp_users at intrepid.danplanet.com
> > http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> > This message was sent to Jim M at jmciver at lmtribune.com
> > To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
> >
> 
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to Nigel Gunn, W8IFF at nigel at ngunn.net
> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com