[chirp_users] programming Yaesu FT2D

[Jardy]

I don't know anything about Linux and have no problems with the many cables I have with the fake Prolific chips in them. Not that hard to roll back the driver if need be. 

Jardy Dawson WA7JRD
Message sent through sub space hailing frequencies using the Universal Translator. 


> On Nov 13, 2016, at 12:37, Nigel A. Gunn G8IFF/W8IFF <nigel at ngunn.net> wrote:
> 
> Try not using Windows. No driver problems with Linux.
> 
> 
>> On 13 November 2016 at 15:19 Jardy Dawson via chirp_users <chirp_users at intrepid.danplanet.com> wrote:
>> 
>> 
>> For Windows, try rolling your Prolific driver back to 3.2.0.0.  Also, make sure cable is FIRMLY pushed in.
>> 
>> Jardy Dawson
>> WA7JRD Ham Radio
>> 
>> Message relayed from secret Hillary Clinton server, located in the basement of her house.  OOPS, you aren't supposed
>> to know that!
>> 
>> On Nov 13, 2016, at 08:49, Robert Carter <carterrj at verizon.net> wrote:
>> 
>> I picked up my general license this year due to an incident I was 
>> involved in -- remote accident with no communications. Just sucked. 
>> Should have studied for the extra license too and gotten them all over 
>> on the same day.
>> 
>> Anyway, I picked up a new Yaesu FT2D yesterday. I'm trying to get over 
>> the programming hump. In the box with the FT2D was a USB programming cable.
>> 
>> Win7:
>> 
>> Yeasu in-the-box supplied Prolific cable and driver from Yeasu's web 
>> site won't run. v1.8 driver fails to install. I downloaded and the 
>> latest v1.16 driver from Prolific's web site, still no love.
>> 
>> Ubutnu 14.04 LTS:
>> 
>> Now it gets interesting. lsubb reports PID/VID for this cable:
>> 
>>   Bus 005 Device 016: ID 26aa:0001
>> 
>> The pl2303 kernel module doesn't recognize this PID/VID as a serial 
>> device. When the cable is inserted, the kernel doesn't load the serial 
>> USB module. "modinfo pl2303" doesn't list this Yeasu cable's PID/VID.
>> 
>> When inserting the USB-serial cable, while the FT2D is in "clone" mode, 
>> syslog reports:
>> 
>> Nov 13 10:20:53 booger kernel: [ 4471.004031] usb 5-1: new full-speed 
>> USB device number 16 using uhci_hcd
>> Nov 13 10:20:58 booger kernel: [ 4476.361065] usb 5-1: New USB device 
>> found, idVendor=26aa, idProduct=0001
>> Nov 13 10:20:58 booger kernel: [ 4476.361073] usb 5-1: New USB device 
>> strings: Mfr=0, Product=0, SerialNumber=0
>> Nov 13 10:20:58 booger mtp-probe: checking bus 5, device 16: 
>> "/sys/devices/pci0000:00/0000:00:1d.3/usb5/5-1"
>> Nov 13 10:20:58 booger mtp-probe: bus: 5, device: 16 was not an MTP device
>> 
>> I tried manually to force load the kernel modules and force the PID/VID 
>> into the drivers -- but still nada:
>> 
>>  sudo modprobe pl2303 vendor=0x26aa product=0x0001
>>  sudo modprobe usbserial vendor=0x26aa product=0x0001
>> 
>> I looked over the CHIRP source code and with the kernel modules "forced" 
>> and the FT2D still in "clone' mode, then launched minicom on 
>> /dev/ttyUSB0. Set the baud rate to 38400 8N1 -- nada. Nothing to/from 
>> the FD2R.
>> 
>> I'm willing to guinea pig here and run some experiments. If anyone has 
>> any ideas, I'd like to hear them.
>> 
>> This should be this hard (well, except for windows).
>> 
>> I checked over the last year of the CHIRP mailing list and didn't find 
>> any posts relative to the FT1D or FT2D, so I guess I'm breaking new ground.
>> 
>> /KC1FAC/
>> _______________________________________________
>> chirp_users mailing list
>> chirp_users at intrepid.danplanet.com
>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>> This message was sent to Jardy at jardy72 at yahoo.com
>> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
>> _______________________________________________
>> chirp_users mailing list
>> chirp_users at intrepid.danplanet.com
>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>> This message was sent to Nigel Gunn, W8IFF at nigel at ngunn.net
>> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to Jardy at jardy72 at yahoo.com
> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20161113/7e78f1b9/attachment.html