[chirp_users] Settings to match Motorola PL tones

Jeffrey fongemie at gmail.com
Wed Jun 8 07:15:21 PDT 2016


Thanks Rick.

I just tried setting Tone Mode to "Tone" with a tone of 67.0 it the UV5R
was able to receive from the Motorola, but the Motorola could not receive
from the UV5R.

"*Tone*: A single CTCSS tone is transmitted, receive squelch is open or
carrier-triggered. The tone used is that which is set in the *Tone*
column.:"

So, if I read this correctly, the Motorola radio transmission is open to
everyone? And will filter out everything that does not transmit with the
correct tone?

Tone mode as "Tone" should work if I have the correct tone, and the radio
is sending it correctly. Right?

Jeff

On Wed, Jun 8, 2016 at 9:55 AM, Rich Messeder <rich.messeder at gmail.com>
wrote:

> I think this is a good question. I have recently acquired 2 BaoFeng
> UV-5RTP. I have programmed them "successfully", but not tested the results.
>
> Here is my take on it.
>
> I think that CHIRP allows the user to select TSQL, indicating that the
> ToneSql value is used for repeater access. It is unfortunate that we all
> don't use the same terms. I opine that CTCSS is the same thing as PL; one
> is a generic term and the other a vendor term.
>
> I understand that Tone in CHIRP is used for receive. If you have Tone
> selected, then the sender must use the agreed tone to open your squelch.
> For repeaters, I am not sure that all repeaters use tone (PL, CTCSS) on
> transmit, as they do on receive. A repeater first senses the carrier on the
> inbound freq, and then look for the PL tone.
>
> My impression is that many radios do not (can not) use PL codes /from/ a
> repeater that are different from the sending PL tone.
>
> Now to 2 radios.
> The sending unit must send the same tone that the receiving unit is
> filtering on. So if you are both working simplex, and you both have tone
> squelch enabled and are using the same PL|CTCSS tones, it should work. I
> might try that later today or tomorrow if I have the time.
>
> From
> http://chirp.danplanet.com/projects/chirp/wiki/MemoryEditorColumns
> Tone
> This sets the CTCSS tone to be transmitted if the Tone Mode is set to
> Tone. In Cross mode, it has additional meanings (see description of Cross
> Mode for more details).
>
> ToneSql
> This sets the CTCSS tone to be transmitted and used for receiver squelch
> if the Tone Mode is set to TSQL. In Cross mode it has additional meanings
> (see description of Cross Mode for more details).
>
> I too have used TSQL for many entries, and now wonder if I should be using
> Tone, because I want to trigger the repeater with a PL tone, but then want
> the reply no matter what.
>
> ~R~ NE1EE
> Short email? No html? Here's why: http://emailcharter.org/
>
> On 2016-06-08 09:26:-0400, Jeffrey wrote:
> >Hey everyone,
> >
> >I'm pretty new to radios in general, and more so programming them, but
> I'll do my best to get the terminology right.
> >
> >I'm trying to use CHIRP to program a UV-5R so that it can communicate
> with a Motorola radio on a certain frequency.  The Motorola is set to use
> 151.9400 with a PL tone of 67.0 for both send and receive.
> >
> >PL is the same as CTCSS correct?
> >
> >On the UV-5R, I've got Tone Mode set as TSQL and ToneSql set to 67.0 -
> and it does not work? The two radios are not communicating.  Am I missing
> something? Something special about Motorola PL tones? Should be a standard
> right?
> >
> >Thanks for any advice.
> >
> >Jeff
> >Jeffrey Fongemie   Â
> >_______________________________________________
> >chirp_users mailing list
> >chirp_users at intrepid.danplanet.com
> >http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> >This message was sent to WeatheredSoul at rich.messeder at gmail.com
> >To unsubscribe, send an email to
> chirp_users-unsubscribe at intrepid.danplanet.com
>
>
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to fongemie at gmail.com at fongemie at gmail.com
> To unsubscribe, send an email to
> chirp_users-unsubscribe at intrepid.danplanet.com
>



-- 
______________

Jeffrey Fongemie

<http://instagram.com/jfongemie>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20160608/2ebcca79/attachment-0002.html 


More information about the chirp_users mailing list