[chirp_users] Freq entry

Gary Runningbear runningbear2000 at gmail.com
Thu Nov 5 09:33:21 PST 2015


That is what I am thinking. Sometimes it also happens when I program from
chirp. Just something I will have to learn to live with I guess.
On Nov 5, 2015 12:31 PM, "David Buss" <kd9ebr at gmail.com> wrote:

> If it doesn't show the offset icons then something isn't right
>
> D. Buss
> KD9EBR
>
> -----Original Message-----
> From: Gary Runningbear <runningbear2000 at gmail.com>
> To: Discussion of CHIRP <chirp_users at intrepid.danplanet.com>
> Sent: Thu, 05 Nov 2015 11:27
> Subject: Re: [chirp_users] Freq entry
>
> This is all very weird. In channel mode fact and offset icons do not show
> that channel will not operate properly . if they do show everything works
> as it should, at least on my uv-82. Too bad the Chinese do not understand
> how Americans want their radios to work. lol
> On Nov 5, 2015 12:19 PM, "David Buss" <kd9ebr at gmail.com> wrote:
>
>> Oops, forgot to say, it should work properly, just not show it.
>>
>> D. Buss
>> KD9EBR
>>
>> -----Original Message-----
>> From: Gary Runningbear <runningbear2000 at gmail.com>
>> To: Discussion of CHIRP <chirp_users at intrepid.danplanet.com>
>> Sent: Thu, 05 Nov 2015 11:14
>> Subject: Re: [chirp_users] Freq entry
>>
>> Just found another problem. I enter a frequency a ct tone and an offset
>> and save to a channel. This is in the VFO of Courts. then I go to channel
>> mode and pull up that channel and find that the CT tone and the offset have
>> not carried over. It is acting like a simplex frequency. did I do something
>> wrong or miss something?
>> On Nov 5, 2015 11:28 AM, "Gary Runningbear" <runningbear2000 at gmail.com>
>> wrote:
>>
>>> Ok. I just figured out how to add up to 5 decimal places. many thanks
>>> On Nov 5, 2015 11:23 AM, "Jim Unroe" <rock.unroe at gmail.com> wrote:
>>>
>>>> On Thu, Nov 5, 2015 at 11:02 AM, Gary Runningbear
>>>> <runningbear2000 at gmail.com> wrote:
>>>> > In the UV 82L, when adding frequencies that have four to five digits
>>>> to the
>>>> > right of the decimal point how do you get  the last one or two digits
>>>> in
>>>> > there?
>>>> >
>>>>
>>>> You just type it into the Frequency cell of the memory spreadsheet
>>>> editor.
>>>>
>>>> If you are talking about entering the frequency into the VFO using the
>>>> keypad (which has nothing to do with CHIRP), you do the following:
>>>>
>>>> 1 set menu 1 (STEP) to a value that is compatible with the frequency
>>>> that you want to enter
>>>> 2 key in the 1st 6 digits of the frequency
>>>> 3 press the [^] up arrow key once
>>>>
>>>> For example if you want to listen to FRS channel, 462.5625 MHz
>>>>
>>>> 1 Set STEP to 2.5KHZ, 6.25KHZ or 12.5KHZ
>>>> 2 Key in 462562 (after entering the last 2, the frequency will be
>>>> rounded off to the 1st STEP compatible frequency below the desired
>>>> frequency)
>>>> 3 Press the [^] up arrow key once (the display will read "462.562"
>>>> followed by a very small 5)
>>>>
>>>> Jim KC9HI
>>>> _______________________________________________
>>>> chirp_users mailing list
>>>> chirp_users at intrepid.danplanet.com
>>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>>>> To unsubscribe, send an email to
>>>> chirp_users-unsubscribe at intrepid.danplanet.com
>>>>
>>>
>> _______________________________________________
>> chirp_users mailing list
>> chirp_users at intrepid.danplanet.com
>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
>> To unsubscribe, send an email to
>> chirp_users-unsubscribe at intrepid.danplanet.com
>>
>
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> To unsubscribe, send an email to
> chirp_users-unsubscribe at intrepid.danplanet.com
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20151105/3d908e4a/attachment-0002.html 


More information about the chirp_users mailing list