[chirp_users] Versions

Bry Carling
Tue Mar 31 06:05:40 PDT 2015


Yes I am sure that is the correct port.

Best regards - Brian Carling
AF4K Crystals Co.
117 Sterling Pine St.
Sanford, FL 32773

Tel: +USA 321-262-5471




> On Mar 31, 2015, at 6:47 AM, John Wuest <ultimafi at yahoo.com> wrote:
> 
> Bry,
> 
> Just a thought...you keep mentioning setting to port 3. Are you sure that is the correct port? Have you plugged the cable into the computer without connecting to the radio, and checked the com port assignment for the cable using device manager? It may not be com 3. Just a thought as I have my first cup of morning coffee.
> 
> John - KZ4KY
> 
> From: Bry Carling AF4K <bcarling at cfl.rr.com>
> To: Discussion of CHIRP <chirp_users at intrepid.danplanet.com>; Jim Unroe <rock.unroe at gmail.com>; David Ranch <chirp at trinnet.net> 
> Sent: Tuesday, March 31, 2015 6:21 AM
> Subject: Re: [chirp_users] Versions
> 
> Thank you very much David,
> 
> After trying many other things...
> 
> I ran the cable loop back tester software, and set to COM3.
> Ran the test and nothing happens. 
> 
> I have tried this with the radio just turned on.
> I have tried this with hreadio in the CLONE mode.
> I have tried this with the radio in the CLONE OUT mode.
> 
> I never get any response. I think perhaps I have a bad cable - sigh!
> 
> One other clue is that the cable makes the radio SCAN whenevr I plug it in normally
> I have to fiddle with it and reinsert it numerous times before it will stop scanning and sit at a 
> fixed frequency.
> 
> The supplier assures me these are not the fake chips but genuine FTDI
> chips he is using, 
> and charged a premium price for it.
> 
> The cable came from Mark Dunkle, KJ6ZWL. I will relay all of this information and see if he can send me another cable that works. 
> 
> Manufacturer: FTDI
> on USB Serial Converter
> 
> Driver Provided: FTDI
> 8/26/2014
> 
> Driver Version:
> 2.12.0.0
> 
> Brian Carling
> 
> 
> 
> 
> 
> On 30 Mar 2015 at 20:33, David Ranch wrote:
> 
> > 
> > Hello Bry,
> > 
> > 
> >    
> >    I set the radio per the cloning instructions and it says: CLONE and then CL OUT m.
> >    Then I click on OK.
> >    
> >    "Failure to communicate with the radio: unexpected response from radio"
> > 
> > 
> > It sounds right... are you sure this cable works?  I know you said it's FTDI based but there have 
> > been counterfit versions of those too.  If you go into the Control Panel --> System --> Device 
> > Manager   Does the serial port show up ok without any warning icons, etc?
> > 
> > 
> > 
> >    
> >    Do I need to change the com port speed or something??
> >    It's set for 8-N-1, 9600 baud
> > 
> > 
> > I think chirp already knows what the serial port needs to be configured for.
> > 
> > 
> >    
> >    Unfortunately, nothing in the Icom manual specifies the data port settings for the CLONE 
> >    function.
> >    
> >    I might just as well have bought a cheap Baofeng I suppose. 
> > 
> > 
> > Naw, I'm sure things will work ok, we're just missing something simple.  Speaking of Baofeng, 
> > push the connector into the radio REALLY hard (I mean HARD) and give it a try again.  That's a 
> > very common problem with cheap cables.
> > 
> > 
> >    
> >    Like I said, I have been trying since january!
> > 
> > 
> > This could be a bad cable.  I think you can connect the TX to RX and using a program like 
> > Hyperterminal, type in characters and see if you see them back.  This is an easy way to see if 
> > things aren't working right
> > 
> >    http://www.kc8unj.com/interface.html
> > 
> > --David
> > KI6ZHD
> > 
> > 
> >    
> >    
> >    
> >    Same problem as before - failure to read radio...
> >    
> >    
> >    
> >    
> >    
> >    On 30 Mar 2015 at 22:13, Jim Unroe wrote:
> >    
> > 
> >    
> >    On Mon, Mar 30, 2015 at 8:29 PM, Bry Carling AF4K <bcarling at cfl.rr.com> wrote:
> > 
> >    
> >    Looks like 0.4.1 is the latest version?
> >    
> >    STILL trying to figure out how to make it work with the Icom T70 here!
> >    
> >    Bry Carling Af4K
> > 
> >    
> >    The CHIRP v0.4.1 daily build will be a year old in April. Use the
> >    latest daily build.
> >    
> >    Jim KC9HI
> > 
> >    
> >    
> >    _______________________________________________
> >    chirp_users mailing list
> >    chirp_users at intrepid.danplanet.com
> >    http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> >    To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
> > 
> > 
> 
> 
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> To unsubscribe, send an email to chirp_users-unsubscribe at intrepid.danplanet.com
> 
> 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20150331/4973d0fc/attachment.html 


More information about the chirp_users mailing list