[chirp_users] Baofeng UV-5R and settings/squelch_levels

Mike Raymond K5HUM at ARRL.NET
Tue Jul 21 08:56:07 PDT 2015


The problem is NOT chirp. chirp runs fine on my W8.1

The problem is the USB to Serial driver.  Which operates
fine on my W7 machine.

The driver error message on the W8.1 machine is:

This device cannot start. (Code 10)
{Not Enough Quota}
Not enough virtual memory or paging file quota is available to complete the
specified operation.

Thanks Mike K5HUM at ARRL.NET


On Tue, Jul 21, 2015 at 10:28 AM, John LaMartina <JohnLa at usa.net> wrote:

> Is the problem potentially Smart Screen?
> Refer to *http://www.miklor.com/COM/UV_CHIRP.php
> <http://www.miklor.com/COM/UV_CHIRP.php>* (section 2)
>
> John
>
> http://www.miklor.com
>
>
>
>
>
>
>
> *From:* chirp_users-bounces at intrepid.danplanet.com [mailto:
> chirp_users-bounces at intrepid.danplanet.com] *On Behalf Of *Mike Raymond
> *Sent:* Tuesday, July 21, 2015 9:25 AM
> *To:* Discussion of CHIRP
> *Subject:* Re: [chirp_users] Baofeng UV-5R and settings/squelch_levels
>
>
>
> Issue:
>
> Cannot get a driver to function on my w8.1 machine using
>
> same cable (with FTDI chip), Win_Driver_Prolific_3_2_0_0
>
> and UV-3R transceiver software that all works FINE on my
>
> big 64b W7 machine incl Chirp.
>
>
>
> Any suggestions on how to solve the W8.1 problems????
>
>
>
> The W8.1 Dell Laptop has 3gb ram, 500gb HD and otherwise
>
> runs flawlessly.
>
>
>
> 73
>
>
>
> On Sun, Jul 19, 2015 at 8:43 PM, Pavel Milanes Costa <co7wt at frcuba.co.cu>
> wrote:
>
>
> El 19/07/15 a las 20:21, Jim Unroe escribió:
>
> > On Sun, Jul 19, 2015 at 11:20 AM, Pavel Milanes Costa
> > <co7wt at frcuba.co.cu> wrote:
> >> Hi, I'm new to the list...
> >>
> >> I was searching the list archives for this, but found no answer, so here
> >> it goes...
> >>
> >> The squelch levels for VHF/UHF on the settings > service settings
> >> options do work for the Baofeng UV-5R?
> >>
> >> My Baofeng is about 10uV in VHF and ~2.0uV on UHF, so VHF reception is
> >> hard, may be it has to do with the SQ level, it has 25 as SQL 0 for VHF
> >> and 19 on SQL 0 for UHF.
> >>
> >> So before I play with that values I want to know if this setting will
> >> really work with my radio.
> >>
> >> I'm using chirp-daily-20150702 here...
> >>
> >> 73,
> >>
> >> --
> >> M.Sc. Pavel Milanes Costa, CO7WT
> >> SYSOP Nodo Gateway CO9JAZ
> >> Ciudad de Camagüey, Camagüey, Cuba.
> >> Cell: (+53) 53-847819
> >>
> >> Este email fue enviado usando packet radio a 9600 baudios
> >> This email was sent using Amateur Packet Radio at 9600 baud
> >
> > There is no guarantee that it will work. Feedback shows that it works
> > for firmware version BFB291 and newer. The settings won't show up if
> > the firmware version is older than this. The improvement seems to vary
> > from firmware version to firmware version and model to model.
> >
> > Always save your radio's channels and settings before you start making
> > any changes. That way you can always get back to where you started. It
> > appears that you have test equipment available. All you have to do is
> > change one setting to see if it works. If it doesn't, then change it
> > back.
> >
> > Jim KC9HI
>
> Thanks for the answer Tim.
>
> My firmware is BFB297 N5R-20, so it may work... I will try and get back
> to the list to report..
>
> 73
>
>
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> To unsubscribe, send an email to
> chirp_users-unsubscribe at intrepid.danplanet.com
>
>
>
> _______________________________________________
> chirp_users mailing list
> chirp_users at intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> To unsubscribe, send an email to
> chirp_users-unsubscribe at intrepid.danplanet.com
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20150721/5411edbd/attachment-0002.html 


More information about the chirp_users mailing list