[chirp_devel] [PATCH 3 of 5] [ft4] compander, 6.25 suppress, freq range fix [#4787]

[Dan Smith]

> @@ -1023,7 +1018,22 @@
>     Pkeys = 2     # number of programmable keys on the FT-4
>     namelen = 6   # length of the mem name display on the FT-4 front-panel
>     id_str = b'IFT-35R\x00\x00V100\x00\x00'
> -
> +    # names for the setmode function for the programmable keys. Mode zero means
> +    # that the key is programmed for a memory not a setmode.
> +    SETMODES = [
> +        "mem", "apo", "ar bep", "ar int", "beclo",              #00-04
> +        "beep", "bell", "cw id", "cw wrt", "dc vlt",            #05-09
> +        "dcs cod", "dt dly", "dt set", "dtc spd", "edg.bep",    #10-14
> +        "lamp", "led.bsy", "led.tx", "lock", "m/t-cl",          #15-19
> +        "mem.del", "mem.tag", "pag.abk", "pag.cdr", "pag.cdt",  #20-24
> +        "pri.rvt", "pswd", "pswdwt", "rf sql", "rpt.ars",       #25-29
> +        "rpt.frq", "rpt.sft", "rxsave", "scn.lmp", "scn.rsm",   #30-34
> +        "skip", "sql.typ", "step", "tn frq", "tot",             #35-39
> +        "tx pwr", "tx save", "vfo.spl", "vox", "wfm.rcv",       #40-44
> +        "w/n.dev", "wx.alert"                                   #45-46
> +        ]
> +    legal_steps = list(STEP_CODE)
> +    legal_steps.remove(6.25)       #should not remove if euro version
> 
> # don't register the FT-65 in the production version until it is tested
> # @directory.register
> @@ -1038,7 +1048,6 @@
>                                    # VHF, RX (136000000, 174000000)
>                                    # UHF, RX (400000000, 480000000)
>         ]
> -    valid_bands = [(108000000, 520000000), (700000000, 999990000)]
>     _valid_chars = chirp_common.CHARSET_ASCII
>     numblocks = 0x215      # number of 16-byte blocks in the radio
>     _memsize = 16 * numblocks   # used by CHIRP file loader to guess radio type
> @@ -1046,4 +1055,20 @@
>     Pkeys = 4     # number of programmable keys on the FT-65
>     namelen = 8   # length of the mem name display on the FT-65 front panel
>     id_str=b'IH-420\x00\x00\x00V100\x00\x00'
> +    # names for the setmode function for the programmable keys. Mode zero means
> +    # that the key is programmed for a memory not a setmode.
> +    SETMODES = [
> +        "mem", "apo", "arts", "battsave", "b-ch.l/o",              # 00-04
> +        "beep", "bell", "compander", "ctcss", "cw id",             # 05-09
> +        "dc volt", "dcs code", "dtmf set", "dtmf wrt", "edg bep",  # 10-14
> +        "key lock", "lamp", "ledbsy", "mem del", "mon/t-cl",       # 15-19
> +        "name tag", "pager", "password", "pri.rvt", "repeater",    # 20-24
> +        "resume", "rf.sql", "scn.lamp", "skip", "sql type",        # 25-29 
> +        "step", "tot", "tx pwr", "tx save", "vfo.spl",             # 30-34
> +        "vox", "wfm.rcv", "wide/nar", "wx alert", "scramble"       # 35-39
> +        ]

This list is the same as the one above, right? Can we define that in one place and use it in both?

--Dan